6 open source boards using the POLOLU_A4988

Real designs built with the POLOLU_A4988, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the POLOLU_A4988

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the POLOLU_A4988 connects to, and the resistors, capacitors and other passives placed on it.

  • Pin 1 is tied to GND on 6 of 6 designs.
  • Pin 7 is tied to GND on 6 of 6 designs.
  • Pin 8 is tied to 12V on 6 of 6 designs.
  • Pin 8 has a decoupling capacitor on 5 of 6 designs, most often 100 µF (then 220 nF).
Pin 1Connected to: GND 100%
Pin 2Connected to: 3.3V 83% · a signal 17%
Pin 7Connected to: GND 100%
Pin 8Connected to: 12V 100%
  • Decoupling capacitor on 83% · 100 µF (2), 220 nF (1)
Pin 9Connected to: POLOLU_A4988 50%, the microcontroller 50%
  • Pull-up to VCC on 33%
Pin 10Connected to: A connector 83%
  • Resistor to GND on 67% · 100 kΩ (2)
Pin 13Connected to: Not connected 67% · 3.3V 17% · a signal 17%
Pin 14Connected to: Not connected 67% · 3.3V 17% · a signal 17%

8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PCB Laser Exposer II by terjeio, ThorControlPCB by AngelLM, ReST32 Main by berryelectronics and XpressoSmoothie by TopherMan.

The POLOLU_A4988 in open source designs

The gallery holds 6 open source boards using the POLOLU_A4988 from 6 GitHub repositories; a typical one measures about 99.8 × 74.1 mm and carries around 68 components.

100% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.

The most starred is PCB Laser Exposer II by terjeio.

Microcontrollers on boards using the POLOLU_A4988

What boards using the POLOLU_A4988 are built for

POLOLU_A4988: common questions

Where can I find a POLOLU_A4988 reference design?

Each of the 6 boards on this page is a real design using the POLOLU_A4988. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the POLOLU_A4988 pin 1 connected?

Pin 1 is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the POLOLU_A4988.

How is the POLOLU_A4988 pin 7 connected?

Pin 7 is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the POLOLU_A4988.

How is the POLOLU_A4988 pin 8 connected?

Pin 8 is tied to 12V on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the POLOLU_A4988.

Which microcontrollers do boards using the POLOLU_A4988 use?

Most are built on AVR/Arduino (1), STM32 (1) and TI MSP430/CC (1).

How big is a typical board using the POLOLU_A4988?

The median is 99.8 × 74.1 mm, and 100% are two-layer designs.

What is the most popular open source board using the POLOLU_A4988?

By GitHub stars, PCB Laser Exposer II by terjeio, with 17 stars.

Can I simulate one of these boards using the POLOLU_A4988 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part