TRELLIS MC MCU Controller

twade12·canopy·hardware/trellis/trellis-mc/trellis-mc.kicad_pcb

TRELLIS MC  MCU Controller PCB layout, top view — open source RP2040/RP2350 board by twade12

About the TRELLIS MC MCU Controller PCB

TRELLIS MC MCU Controller is an open source RP2040/RP2350 PCB design by twade12, published on GitHub. It is a 2-layer board measuring 100 × 80 mm, with 45 components from 23 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the W25Q128JVSIQ, AP2112K-3.3, TCA9548APWR, INA228 and 24AA02E48T. By type, the board carries 21 capacitors, 12 resistors, 7 ICs, 2 connectors, 2 switches and 1 crystal.

From the project

An open-source project to interface with CAN networks to triage and automate testing of automotive modules.

KiCad 9 project skeleton for the minimum-viable Trellis bench: the three boards that prove the whole Canopy→hardware loop before you commit to the power plane, crosspoint, or pattern generator.

- trellis-mc/ — MCU Controller (RP2040, USB to the Pi, I²C/SPI master, VREF sense) — fully captured: 45 components, all nets wired, ERC-clean. - trellis-bp/ — Backplane / Motherboard — skeleton (notes + shared lib). - trellis-se/ — Sensor Emulator — skeleton (notes + shared lib).

Main components on the TRELLIS MC MCU Controller

TRELLIS MC MCU Controller bill of materials (BOM)

45 components, 23 distinct parts.

QtyPartRefs
1
RP2040
U1
1
W25Q128JVSIQ
U2
1
AP2112K-3.3
U3
1
TCA9548APWR
U4
1
INA228
U5
1
24AA02E48T
U6
1
TXS0108EPW
U7
1
12MHz
Y1
1
TRELLIS_Bus_DIN41612_96
J1
1
USB-C
J2
1
RESET
SW1
1
BOOTSEL
SW2
2
15pF
C1, C2
14
100nF
C3, C4, C5, C6, C9, C10, C11, C12 +6
4
1uF
C7, C8, C20, C22
1
10uF
C21
1
1k
R1
1
10
R2
3
10k
R3, R20, R21
2
27
R4, R5
Show 3 more
QtyPartRefs
2
5.1k
R6, R7
2
4.7k
R30, R31
1
0.002
R32

TRELLIS MC MCU Controller design files

The KiCad project lives in the twade12/canopy repository on GitHub; these links point at the commit this page was built from.

TRELLIS MC MCU Controller: common questions

What microcontroller does the TRELLIS MC MCU Controller use?

The TRELLIS MC MCU Controller is built around the RP2040, from the RP2040/RP2350 family.

How big is the TRELLIS MC MCU Controller PCB?

The TRELLIS MC MCU Controller measures 100 × 80 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the TRELLIS MC MCU Controller?

45 components, from 23 distinct parts. The full bill of materials is listed on this page.

Where can I download the TRELLIS MC MCU Controller design files?

From the twade12/canopy repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the TRELLIS MC MCU Controller design in my own project?

The repository has no license, so all rights stay with twade12. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the TRELLIS MC MCU Controller without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards