LineFollower
uHappyLogic·lineFollower·KiCad/robot.kicad_pcb
About the LineFollower PCB
LineFollower is an open source AVR/Arduino PCB design by uHappyLogic, published on GitHub under the GPL-2.0 license. It is a board measuring 125 × 101 mm, with 53 components from 17 distinct parts.
Its main chip is the ATMEGA8A-P, from the AVR/Arduino family. Other key parts include the L293D, 7805 and LM339. By type, the board carries 25 resistors, 17 capacitors, 5 ICs, 3 diodes, 1 crystal and 1 connector.
It belongs with the robotics & motion designs in this gallery.
From the project
2015 LinerFollowers competion hosted by Posen University of Technology winner https://www.youtube.com/watch?v=CigrI7Yh1Fk
Main components on the LineFollower
LineFollower bill of materials (BOM)
53 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATMEGA8A-P | DIP-28__300 | IC1 |
| 1 | L293D | DIP-16__300 | IC2 |
| 1 | 7805 | LM78XXV | U1 |
| 2 | LM339 | DIP-14__300 | U20, U21 |
| 1 | CRYSTAL | HC-49V | X1 |
| 1 | CONN_5X2 | PIN_ARRAY_5x2 | P1 |
| 3 | LED | LED-3MM | D2, D3, D4 |
| 1 | 10uH | R3-LARGE_PADS | L1 |
| 10 | 100nF | C1 | C1, C3, C5, C6, C7, C10, C13, C14 +2 |
| 2 | 47uF | C1V5 | C2, C4 |
| 2 | 22pF | C1V5 | C8, C9 |
| 2 | 10uF | C1V5 | C11, C12 |
| 1 | 22uF | C1V5 | C15 |
| 8 | 10k | R3 | R1, R9, R10, R11, R12, R13, R14, R15 |
| 3 | 150 | R3 | R3, R4, R5 |
| 7 | 240 | R3 | R16, R17, R18, R19, R20, R21, R22 |
| 7 | 100k | R3 | R41, R42, R43, R44, R45, R46, R47 |
LineFollower design files
The KiCad project lives in the uHappyLogic/lineFollower repository on GitHub; these links point at the commit this page was built from.
- LayoutKiCad/robot.kicad_pcb
LineFollower: common questions
What microcontroller does the LineFollower use?
The LineFollower is built around the ATMEGA8A-P, from the AVR/Arduino family.
How big is the LineFollower PCB?
The LineFollower measures 125 × 101 mm and is 1.6 mm thick.
How many components are on the LineFollower?
53 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the LineFollower design files?
From the uHappyLogic/lineFollower repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the LineFollower design in my own project?
Yes, under the terms of its GPL-2.0 license, which uHappyLogic chose for the repository.
Can I test firmware for the LineFollower without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k