8 open source boards using the ATMEGA8A-P

Real designs built with the ATMEGA8A-P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the ATMEGA8A-P

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ATMEGA8A-P connects to, and the resistors, capacitors and other passives placed on it.

  • The PC6/RESET pin has a pull-up to 5V on 5 of 6 designs, most often 10 kΩ.
  • The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 10 nF).
  • The PD2 pin has a series resistor on 4 of 6 designs, most often 300 Ω (then 220 kΩ).
  • The PB6/XTAL1 pin has a crystal on 4 of 6 designs, most often 16 MHz.
PC6/RESETpin 1Connected to: A connector 83%
  • Pull-up to 5V on 83% · 10 kΩ (4)
  • Capacitor to GND on 33% · 100 nF (2)
  • Series resistor on 33% · 100 kΩ (1), 330 Ω (1)
PD0pin 2Connected to: A connector 50% · not connected 17%
  • Series resistor on 33% · 150 Ω (1), 1 kΩ (1)
PD1pin 3Connected to: A connector 50% · not connected 17%
  • Series resistor on 33% · 150 Ω (1), 1 kΩ (1)
PD2pin 4Connected to: Signal 83% · not connected 17%
  • Series resistor on 67% · 300 Ω (1), 220 kΩ (1), 150 Ω (1)
  • Capacitor to GND on 33% · 100 nF (2)
PD3pin 5Connected to: Signal 83% · not connected 17%
  • Series resistor on 50% · 220 kΩ (1), 1 kΩ (1)
  • Capacitor to GND on 33% · 100 nF (2)
PD4pin 6Connected to: Not connected 50% · a signal 50%
  • Series resistor on 33% · 2.2 kΩ (1), 1 kΩ (1)
VCCpin 7Connected to: 5V 83% · a signal 17%
  • Decoupling capacitor on 83% · 100 nF (4), 10 nF (1)
GNDpin 8Connected to: GND 83% · a signal 17%
PB6/XTAL1pin 9Connected to: Signal 83% · not connected 17%
  • Crystal on 67% · 16 MHz (3)
  • Capacitor to GND on 50% · 22 pF (3)
PB7/XTAL2pin 10Connected to: Signal 83% · not connected 17%
  • Crystal on 67% · 16 MHz (3)
  • Capacitor to GND on 50% · 22 pF (3)
PD5pin 11Connected to: Not connected 50% · a signal 50%
  • Series resistor on 33% · 2.2 kΩ (1), 1 kΩ (1)
PD6pin 12Connected to: Signal 83% · not connected 17%
  • Series resistor on 67% · 2.2 kΩ (1), 300 Ω (1), 10 kΩ (1)
PD7pin 13Connected to: Signal 67% · not connected 33%
  • Series resistor on 50% · 2.2 kΩ (1), 300 Ω (1), 1 kΩ (1)
PB0pin 14Connected to: Not connected 67% · a signal 33%
  • Series resistor on 33% · 10 kΩ (1), 1 kΩ (1)
PB1pin 15Connected to: Signal 83% · not connected 17%
  • Series resistor on 50% · 68 kΩ (1), 10 Ω (1)
AVCCpin 20Connected to: 5V 67% · a signal 33%
  • Decoupling capacitor on 50% · 100 nF (3)
AREFpin 21Connected to: Not connected 50% · a signal 50%
  • Capacitor to GND on 33% · 100 nF (2)
AGNDpin 22Connected to: GND 83% · a signal 17%
PC0pin 23Connected to: Signal 83% · not connected 17%
  • Series resistor on 67% · 2.2 kΩ (1), 300 Ω (1), 330 Ω (1)
PC1pin 24Connected to: Signal 83% · not connected 17%
  • Series resistor on 50% · 2.2 kΩ (1), 300 Ω (1), 50 kΩ (1)
PC2pin 25Connected to: Signal 83% · not connected 17%
  • Series resistor on 50% · 2.2 kΩ (1), 50 kΩ (1)
PC3pin 26Connected to: Signal 83% · not connected 17%
  • Series resistor on 50% · 2.2 kΩ (1), 50 kΩ (1)
PC4pin 27Connected to: A connector 33% · not connected 17%
  • Pull-up to VCC on 33% · 100 kΩ (1)
PC5pin 28Connected to: Signal 67% · not connected 33%
  • Series resistor on 33% · 2.2 kΩ (1), 220 kΩ (1)
  • Pull-up to VCC on 33% · 100 kΩ (1)

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Signal.echo by coderarjob, Control by Jonny999999, Throttle tune by Jonny999999 and Rarara by knx444.

The ATMEGA8A-P in open source designs

The gallery holds 8 open source boards using the ATMEGA8A-P from 6 GitHub repositories; a typical one measures about 90 × 100 mm and carries around 52 components.

71% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.

The most starred is Signal.echo by coderarjob.

Parts used alongside the ATMEGA8A-P

Microcontrollers on boards using the ATMEGA8A-P

ATMEGA8A-P: common questions

Where can I find a ATMEGA8A-P reference design?

Each of the 8 boards on this page is a real design using the ATMEGA8A-P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ATMEGA8A-P PC6/RESET pin?

The PC6/RESET pin has a pull-up to 5V on 5 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the ATMEGA8A-P.

What decoupling capacitors do designs use on the ATMEGA8A-P VCC pin?

The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 6 open source designs using the ATMEGA8A-P.

What resistor goes on the ATMEGA8A-P PD2 pin?

The PD2 pin has a series resistor on 4 of 6 designs, most often 300 Ω (then 220 kΩ). Counted from the KiCad layouts of 6 open source designs using the ATMEGA8A-P.

Which microcontrollers do boards using the ATMEGA8A-P use?

Most are built on AVR/Arduino (8).

How big is a typical board using the ATMEGA8A-P?

The median is 90 × 100 mm, and 71% are two-layer designs.

What is the most popular open source board using the ATMEGA8A-P?

By GitHub stars, Signal.echo by coderarjob, with 4 stars.

Can I simulate one of these boards using the ATMEGA8A-P before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part