77 open source boards using the 7805
Real designs built with the 7805, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
NXP
Walter
jochenalt
154.9 × 71.1 mm60 parts2LNo license160Ultra DB X51 v1
ExploreEmbedded
178 × 145 mm132 partsBSD-3-Clause70Cpu board
rjw57
99.1 × 99.1 mm68 parts2LMIT68MCU BaseBoard
ExploreEmbedded
180 × 125 mm146 parts2LNo license25Closed deck x4
OpenLogicEFI
115.5 × 96.2 mm212 parts4LNo license18MCU BaseBoard
ExploreEmbedded
180 × 125 mm146 parts2LNo license17DualLM317BenchSupply
cellularmitosis
99.1 × 99.7 mm49 parts2LMIT12STM32
OwmBoard
kanengomibako
55.4 × 66 mm158 parts2LUnlicense11AVR/Arduino
Cat644
carangil
101.6 × 76.2 mm46 parts2LGPL-2.011QL QsoundQprint clone
alvaroalea
99.1 × 99.1 mm22 parts2LCERN-OHL-S-2.011UMMF
nils-eilers
105 × 100 mm63 parts2LNo license10FreeDSP-CLASSIC-SMD-A
freeDSP
70.4 × 84.4 mm89 parts2LNo license7AVR/Arduino
Thc
festlv
123.8 × 99.7 mm72 parts2LNo license7PIC
YAPSCO-10V
simonjoh
82.8 × 73.2 mm72 parts2LGPL-3.07Raspberry Pi
Battmanpi
andrewerrington
65 × 56 mm76 parts2LGPL-3.06AVR/Arduino
Ultimate temperature controller
Technariumas
80 × 100 mm68 parts2LApache-2.04Analog board
minisystem
200 × 150 mm500 parts2LNo license3AVR/Arduino
Nixiedisp
jtsiomb
140 × 76.1 mm224 parts2LGPL-3.03STM32
Main
UBC-Thunderbots
100 × 100 mm186 partsNo license3AVR/Arduino
CorboIron
bjohan
78.7 × 99.1 mm101 parts2LNo license3AVR/Arduino
MAPusart - USB to USART Bridge using CP2012
MakersAsylumIndia
70 × 30 mm40 parts2LNo license3Breadboard power supply board hardware design
SolderedElectronics
54 × 29.5 mm24 parts2LTAPR-OHL-1.03MCU BaseBoard
AhmedElwakeel
180 × 125 mm146 parts2LNo license1AVR/Arduino
SignalGenerator
ukmaker
99.8 × 100 mm115 parts2LNo license1OpAmpPassXsistorBenchSupply
cellularmitosis
99.7 × 99.7 mm87 parts2LMIT1Scanner
cellularmitosis
99.1 × 132.1 mm64 parts2LMIT1SERIAL PIC PROGRAMMER
zymaxcii
160 × 99.1 mm55 partsNo license1ReFil
n0skill
50.6 × 30 mm19 parts2LNo license1ESP32
PLL AM OSC 1 7
Gloeidraad
160 × 100 mm168 parts2LNo license0Thermocouple
meowthink
150 × 70 mm168 parts2LNo license0MystiqueJamma
rflamino
140.4 × 114.8 mm164 partsNo license0MCU BaseBoard
ExploreEmbedded
180 × 125 mm146 parts2LNo license0MCU BaseBoard
ExploreEmbedded
180 × 125 mm146 parts2LNo license0Ultra DB X51 v1
shivamag00
178 × 145 mm132 partsNo license0Gsa d1
tjb803
100 × 100 mm94 parts2LMIT0DMX-dimmer pack
hsiboy
100.1 × 100 mm90 partsNo license0
How designs wire the 7805
Read from the KiCad layouts of 58 open source designs, one per repository: what each pin of the 7805 connects to, and the resistors, capacitors and other passives placed on it.
- The IN pin has a capacitor to GND on 25 of 42 designs, most often 100 nF (then 220 µF).
- Pin GND is tied to GND on 22 of 22 designs.
- Pin VO has a decoupling capacitor on 15 of 21 designs, most often 100 µF (then 10 µF).
- The VO_3 pin has a decoupling capacitor on 14 of 35 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| INpin 1 | Connected to: Signal 52% · not connected 17% · 12V 31% |
|
| GNDpin 2 | Connected to: GND 74% · not connected 17% | — |
| VO_3pin 3 | Connected to: 5V 80% · a signal 17% |
|
| Pin GND | Connected to: GND 100% | — |
| Pin VI | Connected to: 12V 71% · a signal 29% |
|
| Pin VO | Connected to: 5V 57% · a signal 43% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Walter by jochenalt, SERIAL PIC PROGRAMMER by claynicholson, Booster-Link by GBert and Ultra DB X51 v1 by ExploreEmbedded.
The 7805 in open source designs
The gallery holds 77 open source boards using the 7805 from 64 GitHub repositories; a typical one measures about 100 × 99.1 mm and carries around 61 components.
98% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Walter by jochenalt.
Parts used alongside the 7805
Microcontrollers on boards using the 7805
What boards using the 7805 are built for
7805: common questions
Where can I find a 7805 reference design?
Each of the 77 boards on this page is a real design using the 7805. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 7805 IN pin connected?
The IN pin has a capacitor to GND on 25 of 42 designs, most often 100 nF (then 220 µF). Counted from the KiCad layouts of 58 open source designs using the 7805.
How is the 7805 pin GND connected?
Pin GND is tied to GND on 22 of 22 designs. Counted from the KiCad layouts of 58 open source designs using the 7805.
What decoupling capacitors do designs use on the 7805 pin VO?
Pin VO has a decoupling capacitor on 15 of 21 designs, most often 100 µF (then 10 µF). Counted from the KiCad layouts of 58 open source designs using the 7805.
What parts are used alongside the 7805?
The L293D, 24C16, DS1307, 74HC125 and LM358 appear in the most repositories here.
Which microcontrollers do boards using the 7805 use?
Most are built on AVR/Arduino (18), PIC (8), ESP32 (3) and STM32 (2).
How big is a typical board using the 7805?
The median is 100 × 99.1 mm, and 98% are two-layer designs.
What is the most popular open source board using the 7805?
By GitHub stars, Walter by jochenalt, with 160 stars.
Can I simulate one of these boards using the 7805 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.