Transmitter
UltraInstinct21·Kicad_Projects·2.TRANSMITTER_RECEIVER/transmitter/transmitter.kicad_pcb
About the Transmitter PCB
Transmitter is an open source AVR/Arduino PCB design by UltraInstinct21, published on GitHub. It is a 2-layer board measuring 100 × 70 mm, with 9 components from 8 distinct parts.
Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the NRF24L01_Breakout and AMS1117. By type, the board carries 4 ICs, 1 module, 1 battery holder, 1 switch and 1 capacitor.
From the project
Beginner kicad projects
1. Buck Converter To convert 24V to 12V , 5V 2A and 3.3V 2A.
2. Transmitter and Receiver A 7-channel transmitter and receiver using NRF24L01 and Arduino Nano.
Main components on the Transmitter
Transmitter bill of materials (BOM)
9 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NRF24L01_Breakout | nRF24L01_Breakout | U1 |
| 1 | AMS1117 | SOT-223-3_TabPin2 | U2 |
| 2 | ~ | JOYSTICK-PSP1000 | U3, U4 |
| 1 | Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 1 | Battery | BatteryHolder_MPD_BA9VPC_1xPP3 | BT1 |
| 1 | R_Potentiometer | Potentiometer_Alps_RK09K_Single_Vertical | RV1 |
| 1 | SW_Nidec_CAS-120A1 | Nidec_Copal_CAS-120A | SW1 |
| 1 | 10uf | C_Radial_D4.0mm_H5.0mm_P1.50mm | C1 |
Transmitter design files
The KiCad project lives in the UltraInstinct21/Kicad_Projects repository on GitHub; these links point at the commit this page was built from.
Transmitter: common questions
What microcontroller does the Transmitter use?
The Transmitter is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.
How big is the Transmitter PCB?
The Transmitter measures 100 × 70 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Transmitter?
9 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the Transmitter design files?
From the UltraInstinct21/Kicad_Projects repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Transmitter design in my own project?
The repository has no license, so all rights stay with UltraInstinct21. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Transmitter without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in Kicad_Projects
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k