106 open source boards using the NRF24L01_Breakout
Real designs built with the NRF24L01_Breakout, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Abn6502
AndersBNielsen
149.9 × 74.9 mm142 parts2LCC-BY-NC-4.094AVR/Arduino
Capacitive soil moisture sensor
RonMcKay
185.3 × 23 mm18 parts2LNo license88Raspberry Pi
Cs240lx-22spr
dddrrreee
67.3 × 45.7 mm6 parts2LMIT27AVR/Arduino
V usb businesscard
AndersBNielsen
85 × 54 mm31 parts2LGPL-3.017ESP32
OpenDTU BreakoutBoard
marove2000
35 × 55 mm12 parts2LCC-BY-SA-4.016STM32
Astra v2
TheScientist101
35 × 32.4 mm41 parts4LCC-BY-NC-4.010Microchip SAM
Femto satellite
spel-uchile
103.1 × 54 mm38 parts2LGPL-3.09STM32
Nrf24stm8l
TG9541
17.8 × 29.2 mm11 parts2LMIT8ESP32
ESP32-MySensors-Gateway
freynder
55 × 95 mm47 parts2LNo license5ESP32
Niphar
mornepousse
340.8 × 104.7 mm275 parts4LMIT4Microchip SAM
FOD
spel-uchile
82.5 × 29 mm35 parts2LGPL-3.04AVR/Arduino
Kombo nrf24 atmega8
MelexinVN
37.6 × 30.7 mm24 parts2LGPL-3.03ESP32
Milight hub
usimd
30.2 × 19.8 mm22 parts2LCERN-OHL-S-2.03ESP32
RC Car Main Onboard
cjg-1
147.3 × 78.1 mm51 parts4LNo license2Deltavr controller
oxy-2
70 × 70 mm46 parts2LMIT2Bs base
MelexinVN
99.1 × 99.1 mm24 parts2LGPL-3.02STM32
Kombo nrf24 stm32f030
MelexinVN
30.5 × 30.5 mm21 parts2LGPL-3.02ESP-Marauder
R09Aditya
72 × 154.5 mm10 parts2LNo license2AVR/Arduino
Control panel
lucanastasio
65 × 58 mm158 parts2LNo license1RP2040/RP2350
RP2040 minimal - Copy
leonidas213
99.8 × 99.2 mm102 parts2LNo license1STM32
ProDroidVR
xxdamlaxx
30 × 100 mm61 parts4LMIT1STM32
Kikad project
Sashabg1228
100 × 110 mm49 parts2LNo license1AVR/Arduino
Transmitter
damianmoore
63 × 40.6 mm37 parts2LNo license1Esp32-jammer
sohamboyythrdh6
60 × 110 mm17 parts4LNo license1AVR/Arduino
VoidLens-DIY-VR-Headset-Prototype1
scattercat-123
88.2 × 45.5 mm15 parts2LNo license1AVR/Arduino
Rolltech
kajgm
100 × 49 mm11 parts2LNo license1ESP32
Tuffboy
ishantdahiya1501-ctrl
52.5 × 90.5 mm7 parts2LNo license1Pathfinder-Mark-IV
MagicalPotato715
97 × 95 mm92 parts4LNo license0AVR/Arduino
TransmitterV2
RobbeElsermans
35.6 × 99.8 mm75 parts2LApache-2.00ESP32
Bonk
tyke01
125 × 100 mm72 parts4LNo license0STM32
Hw rc car pad
bszyca
149.5 × 66 mm71 parts4LNo license0ESP32
Conchodytes
mornepousse
39 × 81.6 mm64 parts4LNo license0Helpers-Keyboard
siliwho
90.2 × 90.2 mm61 parts2LNo license0AVR/Arduino
BlanceCarProject
Andy-Cheng1017
77.9 × 21.1 mm55 parts2LNo license0ESP32
Trackball
mornepousse
52 × 72.1 mm51 parts2LNo license0STM32
Rc helicopter mainboard
ikajdan
50 × 50 mm49 parts2LCERN-OHL-P-2.00
How designs wire the NRF24L01_Breakout
Read from the KiCad layouts of 75 open source designs, one per repository: what each pin of the NRF24L01_Breakout connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 35 of 75 designs, most often 10 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 89% | — |
| VCCpin 2 | Connected to: 3.3V 76% · a signal 21% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Baseboard 2slots by OpenLightingProject, Abn6502 by AndersBNielsen, Capacitive soil moisture sensor by RonMcKay and Control v4.0 by RoboJackets.
The NRF24L01_Breakout in open source designs
The gallery holds 106 open source boards using the NRF24L01_Breakout from 77 GitHub repositories; a typical one measures about 66.9 × 57.5 mm and carries around 22 components.
84% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.
The most starred is Baseboard 4slots by OpenLightingProject.
Parts used alongside the NRF24L01_Breakout
Microcontrollers on boards using the NRF24L01_Breakout
What boards using the NRF24L01_Breakout are built for
NRF24L01_Breakout: common questions
Where can I find a NRF24L01_Breakout reference design?
Each of the 106 boards on this page is a real design using the NRF24L01_Breakout. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the NRF24L01_Breakout VCC pin?
The VCC pin has a decoupling capacitor on 35 of 75 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 75 open source designs using the NRF24L01_Breakout.
What parts are used alongside the NRF24L01_Breakout?
The AMS1117-3.3, ESP32-S3-WROOM-1, Arduino_Nano_v3.x, COM-09032 and TP4056-42-ESOP8 appear in the most repositories here.
Which microcontrollers do boards using the NRF24L01_Breakout use?
Most are built on AVR/Arduino (32), ESP32 (22), STM32 (15) and RP2040/RP2350 (7).
How big is a typical board using the NRF24L01_Breakout?
The median is 66.9 × 57.5 mm, and 84% are two-layer designs.
What is the most popular open source board using the NRF24L01_Breakout?
By GitHub stars, Baseboard 4slots by OpenLightingProject, with 128 stars.
Can I simulate one of these boards using the NRF24L01_Breakout before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.