My half life project
Userofhackclub·my-half-life-project
About the My half life project PCB
My half life project is an open source ESP32 PCB design by Userofhackclub, published on GitHub. It is a 2-layer board measuring 104 × 87 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
From the project
For me this project meant learning a whole new world of tinkering and creation that I have not experienced up to this point.
For me this project meant learning a whole new world of tinkering and creation that I have not experienced up to this point.
Kicad was the tool of choice for this project, and I followed the handy Starbie guide here on github in order to create my very own starbie. Here is the link to the Starbie guide!
The Starbie itself is similar in function to a retro Tamagochi toy with sensors and buttons for added functionality.
Main components on the My half life project
My half life project bill of materials (BOM)
7 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U1 |
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U2 |
| 1 | CONN_01X04_PIN Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | CONN_01X08_PIN Conn_01x08_Pin | MPU6050_Module | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10K | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
My half life project design files
The KiCad project lives in the Userofhackclub/my-half-life-project repository on GitHub; these links point at the commit this page was built from.
- LayoutMy_first_project.kicad_pcb
- SchematicMy_first_project.kicad_sch
- BOMbom.csv
My half life project: common questions
What microcontroller does the My half life project use?
The My half life project is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the My half life project PCB?
The My half life project measures 104 × 87 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the My half life project?
7 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the My half life project design files?
From the Userofhackclub/my-half-life-project repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the My half life project design in my own project?
The repository has no license, so all rights stay with Userofhackclub. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the My half life project without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k