MSP430 Breakout

UWCubeSat·HS1_Motor_Test·MSP430 Breakout/MSP430 Breakout.kicad_pcb

MSP430 Breakout layout, top view — open source TI MSP430/CC board by UWCubeSat

About the MSP430 Breakout

MSP430 Breakout is an open source TI MSP430/CC PCB design by UWCubeSat, published on GitHub under the MIT license. It is a 2-layer board measuring 63.5 × 63.5 mm, with 35 components from 24 distinct parts.

Its main chip is the MSP430FR5994IPM, from the TI MSP430/CC family. Other key parts include the LP2985-3.3. By type, the board carries 14 capacitors, 9 connectors, 6 resistors, 2 ICs, 2 crystals and 1 switch.

It belongs with the robotics & motion and dev boards & breakouts designs in this gallery.

From the project

BLDC motor driver for testing HS1 RW motors

Main components on the MSP430 Breakout

MSP430FR5994IPMLP2985-3.3

MSP430 Breakout bill of materials (BOM)

35 components, 24 distinct parts.

QtyPartRefs
1
MSP430FR5994IPM
U1
1
LP2985-3.3
U2
1
32k
Y1
1
16M
Y2
1
Conn_DRV
J1
1
Conn_BNO_6
J2
1
Conn_BNO_4
J3
1
Conn_Jumper
J4
1
Conn_JTAG
J5
1
Conn_5V
J6
1
Conn_I2C
J7
1
Conn_3.3V
J8
1
Conn_GPIO
J9
1
SW_RESET
SW1
1
LED
D1
4
10p
C1, C2, C6, C7
3
1u
C3, C4, C5
3
100n
C8, C9, C10
2
4.7u
C11, C13
1
1n
C12
Show 4 more
QtyPartRefs
1
0.01u
C14
4
10k
R1, R2, R3, R4
1
47k
R5
1
470
R6

MSP430 Breakout design files

The KiCad project lives in the UWCubeSat/HS1_Motor_Test repository on GitHub; these links point at the commit this page was built from.

MSP430 Breakout: common questions

What microcontroller does the MSP430 Breakout use?

The MSP430 Breakout is built around the MSP430FR5994IPM, from the TI MSP430/CC family.

How big is the MSP430 Breakout?

The MSP430 Breakout measures 63.5 × 63.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the MSP430 Breakout?

35 components, from 24 distinct parts. The full bill of materials is listed on this page.

Where can I download the MSP430 Breakout design files?

From the UWCubeSat/HS1_Motor_Test repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the MSP430 Breakout design in my own project?

Yes, under the terms of its MIT license, which UWCubeSat chose for the repository.

Can I test firmware for the MSP430 Breakout without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug TI MSP430/CC firmware against it before you order a PCB.

More boards in HS1_Motor_Test

Similar boards