Formlabs wash sensor
uwmakerspace·formlabs-wash-sensor·kicad/Distance Sensor.kicad_pcb
About the Formlabs wash sensor PCB
Formlabs wash sensor is an open source ESP32 PCB design by uwmakerspace, published on GitHub under the MIT license. It is a 2-layer board measuring 33 × 24 mm, with 2 components from 2 distinct parts.
Its main chip is the ESP32-C3_SUPERMINI_SMD, from the ESP32 family. By type, the board carries 1 IC and 1 connector.
It belongs with the displays & leds and sensors designs in this gallery.
From the project
Detects when Formlabs Wash Stations have finished and uses a strip of NeoPixels to visibly notify completion
This repository contains the firmware and documentation for the Design Innovation Lab's Formlabs Wash Sensor. This device is designed to monitor multiple Formlabs Wash units and visually alert when a wash has completed.
The device uses a distance sensor to measure the position of the wash basket. If the sensor detects the back wall, it assumes the machines are empty or currently working. If it detects an object (the basket/print) consistently, it illuminates a WS2812B LED strip to indicate presence and position, providing visual feedback in busy environments.

Main components on the Formlabs wash sensor
Formlabs wash sensor bill of materials (BOM)
2 components, 2 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3_SUPERMINI_SMD | MODULE_ESP32-C3_SUPERMINI | U3 |
| 1 | Conn_01x03 | PinHeader_1x03_P2.54mm_Vertical | J1 |
Formlabs wash sensor design files
The KiCad project lives in the uwmakerspace/formlabs-wash-sensor repository on GitHub; these links point at the commit this page was built from.
Formlabs wash sensor: common questions
What microcontroller does the Formlabs wash sensor use?
The Formlabs wash sensor is built around the ESP32-C3_SUPERMINI_SMD, from the ESP32 family.
How big is the Formlabs wash sensor PCB?
The Formlabs wash sensor measures 33 × 24 mm, has 2 copper layers and is 1.6256 mm thick.
How many components are on the Formlabs wash sensor?
2 components, from 2 distinct parts. The full bill of materials is listed on this page.
Where can I download the Formlabs wash sensor design files?
From the uwmakerspace/formlabs-wash-sensor repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Formlabs wash sensor design in my own project?
Yes, under the terms of its MIT license, which uwmakerspace chose for the repository.
Can I test firmware for the Formlabs wash sensor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k