HardLabs

Robosub teensy

valex2·poseidon·1-Gen1/Teensy_Board/robosub_teensy.kicad_pcb

Robosub teensy PCB layout, top view — open source NXP board by valex2

About the Robosub teensy PCB

Robosub teensy is an open source NXP PCB design by valex2, published on GitHub. It is a 4-layer board measuring 120 × 64 mm, with 27 components from 27 distinct parts.

Its main chip is the INA300AIDSQT, from the NXP family. Other key parts include the SN74LVC1G97DBVR. By type, the board carries 25 connectors and 2 ICs.

From the project

Stanford Robosub Electrical Repository

DO NOT RUN FOR MORE THAN 10 SECONDS WHILE OUTSIDE OF WATER

Use serial library in Python, and write as follows: > portName.write(b"thrusternumber delayvalue")

Main components on the Robosub teensy

INA300AIDSQTSN74LVC1G97DBVR

Robosub teensy bill of materials (BOM)

27 components, 27 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
INA300AIDSQT
Teensy4.1
Texas Instruments
U1
1
SN74LVC1G97DBVR
Teensy4.0_AudioShield_REVD
Texas Instruments
U2
1
1135333
T1
Pheonix Contact
J1
1
1135333
UART
Pheonix Contact
J2
1
1135333
T2
Pheonix Contact
J3
1
1135333
T6
Pheonix Contact
J4
1
1135333
T3
Pheonix Contact
J5
1
1135333
T7
Pheonix Contact
J6
1
1135333
T4
Pheonix Contact
J7
1
1135333
T8
Pheonix Contact
J8
1
1135333
T5
Pheonix Contact
J9
1
1135333
PixHawk PM02
Pheonix Contact
J10
1
3.3V Power
J11
1
5V Power
J12
1
BUS1
J13
1
CONN_01X04
BUS2
J14
1
Digital Pins
J17
1
BUS3
J18
1
BUS4
J19
1
BUS5
J20
Show 7 more
QtyPartRefs
1
BUS6
J21
1
SPI1
J22
1
SPI2
J23
1
I2C_2
J24
1
I2C_3
J25
1
SPI3
J26
1
SPI4
J27

Robosub teensy design files

The KiCad project lives in the valex2/poseidon repository on GitHub; these links point at the commit this page was built from.

Robosub teensy: common questions

What microcontroller does the Robosub teensy use?

The Robosub teensy is built around the INA300AIDSQT, from the NXP family.

How big is the Robosub teensy PCB?

The Robosub teensy measures 120 × 64 mm, has 4 copper layers and is 1.769872 mm thick.

How many components are on the Robosub teensy?

27 components, from 27 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Robosub teensy design files?

From the valex2/poseidon repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Robosub teensy design in my own project?

The repository has no license, so all rights stay with valex2. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Robosub teensy without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.

More boards in poseidon

Similar boards