Smart-PowerMeter-PCB-using-ESP-32
Vedevil·Smart-PowerMeter-PCB-using-ESP-32
About the Smart-PowerMeter-PCB-using-ESP-32
Smart-PowerMeter-PCB-using-ESP-32 is an open source ESP32 PCB design by Vedevil, published on GitHub under the MIT license. It is a 2-layer board measuring 84.4 × 54.8 mm, with 44 components from 25 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the CH340C and AMS1117-3.3. By type, the board carries 11 capacitors, 10 resistors, 6 connectors, 6 diodes, 3 ICs and 2 transistors.
It belongs with the iot & wireless and sensors designs in this gallery.
From the project
ESP32-based Smart Power Monitoring PCB with PZEM-004T, ACS712, and SCT013 sensors
The Smart Power Monitor PCB is an open-source hardware project built around the ESP32-WROOM-32 microcontroller, designed to measure and monitor voltage, current, power, and energy consumption in real time.
This PCB integrates support for three widely used energy measurement modules:
PZEM-004T – For accurate voltage, power, and energy measurement.
ACS712 – A Hall-effect current sensor for low-current measurements.
Main components on the Smart-PowerMeter-PCB-using-ESP-32
Smart-PowerMeter-PCB-using-ESP-32 bill of materials (BOM)
44 components, 25 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH340C | SOIC-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U3 |
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U4 |
| 2 | SS8050 | SOT-23 | Q1, Q2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | ACS712 | JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J2 |
| 1 | AudioJack3 | Jack_3.5mm_CUI_SJ-3523-SMT_Horizontal | J3 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | PZEM-004T | JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J5 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_bornier-2_P5.08mm | J6 |
| 1 | 1K | R_0805_2012Metric | 1K1 |
| 2 | 56 | R_0805_2012Metric | 2K1, 56ohm1 |
| 1 | HLK-PM01 | Converter_ACDC_Hi-Link_HLK-PMxx | PS1 |
| 2 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 3 | LESD5D5.0CT1G | TVS_LESD5D5.0CT1G | D1, D2, D4 |
| 1 | SS34 | D_SMA | D3 |
| 2 | LED | LED_0603_1608Metric | D5, D14 |
| 3 | 10uF | C_1206_3216Metric | C2, C5, C7 |
| 6 | 0.1uF | C_0603_1608Metric | C3, C8, C9, C10, C11, C12 |
| 1 | 10uF/25V | C_0603_1608Metric | C4 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10nf | C_1206_3216Metric | C6 |
| 2 | 5.1K | R_0603_1608Metric | R2, R3 |
| 2 | 2K2 | R_0603_1608Metric | R4, R17 |
| 2 | 0E | R_0603_1608Metric | R9, R12 |
| 4 | 10k | R_0603_1608Metric | R10, R11, R13, R14 |
Smart-PowerMeter-PCB-using-ESP-32 design files
The KiCad project lives in the Vedevil/Smart-PowerMeter-PCB-using-ESP-32 repository on GitHub; these links point at the commit this page was built from.
- Layoutpower_meter_new.kicad_pcb
- Schematicpower_meter_new.kicad_sch
Smart-PowerMeter-PCB-using-ESP-32: common questions
What microcontroller does the Smart-PowerMeter-PCB-using-ESP-32 use?
The Smart-PowerMeter-PCB-using-ESP-32 is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Smart-PowerMeter-PCB-using-ESP-32?
The Smart-PowerMeter-PCB-using-ESP-32 measures 84.4 × 54.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Smart-PowerMeter-PCB-using-ESP-32?
44 components, from 25 distinct parts. The full bill of materials is listed on this page.
Where can I download the Smart-PowerMeter-PCB-using-ESP-32 design files?
From the Vedevil/Smart-PowerMeter-PCB-using-ESP-32 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Smart-PowerMeter-PCB-using-ESP-32 design in my own project?
Yes, under the terms of its MIT license, which Vedevil chose for the repository.
Can I test firmware for the Smart-PowerMeter-PCB-using-ESP-32 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k