HardLabs

Smart plants breakout ws board rev2

vektorious·hpi_smart_plants·hardware/pcb/smart_plants_breakout_ws-board_rev2/smart_plants_breakout_ws-board_rev2.kicad_pcb

Smart plants breakout ws board rev2 layout, top view — open source ESP32 board by vektorious

About the Smart plants breakout ws board rev2

Smart plants breakout ws board rev2 is an open source ESP32 PCB design by vektorious, published on GitHub under the MIT license. It is a 2-layer board measuring 48 × 70 mm, with 17 components from 14 distinct parts.

Its main chip is the Waveshare ESP32-C6-Nano, from the ESP32 family. By type, the board carries 6 resistors, 2 connectors, 2 diodes, 2 capacitors, 1 IC and 1 transistor.

It belongs with the dev boards & breakouts designs in this gallery, and the repository also holds 1 earlier revision of it.

From the project

Two active PCB designs are maintained, one per supported controller board. Both route sensors to the same GPIO numbers, so no firmware changes are needed between variants.

Two active PCB designs are maintained, one per supported controller board. Both route sensors to the same GPIO numbers, so no firmware changes are needed between variants.

The primary board used in student workshops. Designed for the Waveshare ESP32-C6 Zero.

- Gerber files: spwsbreakoutrev2/ folder and spwsbreakoutrev2.zip - KiCAD project: smartplantsbreakoutws-boardrev2.kicadpro - Firmware pin config: active block in code/spmodular/config.h

Main components on the Smart plants breakout ws board rev2

Waveshare ESP32-C6-Nano

Smart plants breakout ws board rev2 bill of materials (BOM)

17 components, 14 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
Waveshare ESP32-C6-Nano
U1
1
IRLZ14
Q1
2
Conn_01x09_Pin
J1, J2
1
I2C
I2C
1
I2C D2-powered
I2C D2-powered
1
I2C D3-powered
I2C D3-powered
1
1N4001
D1
1
1N5817
D2
1
220µF
C2
1
22µF
C3
2
220k
R1, R2
1
10k
R3
1
22R
R4
2
4k7
R5, R6

Smart plants breakout ws board rev2 design files

The KiCad project lives in the vektorious/hpi_smart_plants repository on GitHub; these links point at the commit this page was built from.

Smart plants breakout ws board rev2: common questions

What microcontroller does the Smart plants breakout ws board rev2 use?

The Smart plants breakout ws board rev2 is built around the Waveshare ESP32-C6-Nano, from the ESP32 family.

How big is the Smart plants breakout ws board rev2?

The Smart plants breakout ws board rev2 measures 48 × 70 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Smart plants breakout ws board rev2?

17 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Smart plants breakout ws board rev2 design files?

From the vektorious/hpi_smart_plants repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Smart plants breakout ws board rev2 design in my own project?

Yes, under the terms of its MIT license, which vektorious chose for the repository.

Can I test firmware for the Smart plants breakout ws board rev2 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in hpi_smart_plants

Earlier revisions in the repo: smart_plants_breakout_ws-board_rev1

Similar boards