Proto mcxe246
via·viaems-boards·proto-mcxe246/proto-mcxe246.kicad_pcb
About the Proto mcxe246 PCB
Proto mcxe246 is an open source STM32 PCB design by via, published on GitHub. It is a 2-layer board measuring 34 × 78 mm, with 50 components from 33 distinct parts.
Its main chip is the TC442XA, from the STM32 family. Other key parts include the LM2940. By type, the board carries 16 capacitors, 13 resistors, 12 connectors, 4 ICs, 4 diodes and 1 crystal.
From the project
ViaEMS PCB Designs
Power schemes: - USB Power -> 5v Vdd (3.3v Reg powering uart) - USB Power -> 3v3 Vdd - SWD 3.3 V power -> 3v3 Vdd. Uart? Only if 5vusb jumpered. -
Fixes: - Crystal series resistor is on wrong pin! - 1M parallel should be DNP. Rs should be 0 ohms not 220.
- The ground ring is supposed to not be connected to other grounds, the bottom is also suppsoed to be a ring, vias only connect the two
Main components on the Proto mcxe246
Proto mcxe246 bill of materials (BOM)
50 components, 33 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM2940 MCP1754S-3302xCB | SOT-23 | U1 |
| 1 | TC442XA STM32C071K8Ux | QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U3 |
| 1 | TC442XA TXB0104BQA | DHWQFN-14-1EP_2.5x3mm_P0.5mm_EP1x1.5mm | U4 |
| 1 | TC442XA FS32K144HAT0MLHT | LQFP-64_10x10mm_P0.5mm | U5 |
| 1 | 16 MHz | Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | CONN_01X02 5V_usb | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | CONN_01X03 5V | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | CONN_01X04 5V | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | CONN_01X02 PWR_SEL | PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | CONN_01X04 USB_C_Receptacle_USB2.0 | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J7 |
| 1 | CONN_01X04 SPARE | PinHeader_2x03_P2.54mm_Vertical | J8 |
| 2 | CONN_01X02 Conn_02x08_Odd_Even | PinHeader_2x08_P2.54mm_Vertical | J12, J16 |
| 1 | CONN_01X06 Conn_02x08_Odd_Even | PinHeader_2x08_P2.54mm_Vertical | J13 |
| 1 | CONN_01X06 Conn_ARM_JTAG_SWD_10 | PinHeader_2x05_P1.27mm_Vertical_SMD | J14 |
| 1 | CONN_02X06_ODD_EVEN Conn_02x08_Odd_Even | PinHeader_2x08_P2.54mm_Vertical | J15 |
| 1 | CONN_01X04 Conn_ARM_JTAG_SWD_10 | PinHeader_2x05_P1.27mm_Vertical_SMD | J17 |
| 2 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D4 |
| 1 | ZEN056V115A24LS LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | BAT54S LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 1 | 10 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
Show 13 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 47 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 5 | 0.1 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C11, C12, C13, C17 |
| 3 | 1UF 0.1 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C7, C10 |
| 2 | 1UF 10 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6, C9 |
| 1 | 1UF 4.7 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8 |
| 1 | 1 nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C14 |
| 2 | 7 pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C15, C16 |
| 4 | 100K 220 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3, R12, R13 |
| 2 | 100K 5.1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R4 |
| 1 | 0 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 1 | 1M | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 4 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7, R8, R9, R10 |
| 1 | 100K 10k | R_0805_2012Metric | R11 |
Proto mcxe246 design files
The KiCad project lives in the via/viaems-boards repository on GitHub; these links point at the commit this page was built from.
Proto mcxe246: common questions
What microcontroller does the Proto mcxe246 use?
The Proto mcxe246 is built around the TC442XA, from the STM32 family.
How big is the Proto mcxe246 PCB?
The Proto mcxe246 measures 34 × 78 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Proto mcxe246?
50 components, from 33 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Proto mcxe246 design files?
From the via/viaems-boards repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Proto mcxe246 design in my own project?
The repository has no license, so all rights stay with via. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Proto mcxe246 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in viaems-boards
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k