ESP32C6-CAN
vk-sahni·ESP32C6-CAN
About the ESP32C6-CAN PCB
ESP32C6-CAN is an open source ESP32 PCB design by vk-sahni, published on GitHub. It is a 4-layer board measuring 40 × 25 mm, with 57 components from 33 distinct parts.
Its main chip is the ESP32-C6FH4, from the ESP32 family. Other key parts include the TC2014-3.3VxCTTR, TCAN332 and 74LVC1G125. By type, the board carries 18 capacitors, 18 resistors, 6 connectors, 5 diodes, 4 ICs and 2 switches.
It belongs with the iot & wireless, robotics & motion and rf & radio designs in this gallery.
From the project
ESP32-C6 CAN telemetry gateway for ArduPilot/DroneCAN — captures CAN data and forwards flight telemetry to cloud services over Wi-Fi/Internet, with local MicroSD logging and buffering.
A hardware design for an ESP32-C6 edge telemetry gateway for UAVs and robotics. It is intended to sit alongside an ArduPilot flight controller and expose CAN / DroneCAN, Wi-Fi-capable MCU, USB-C, and MicroSD hardware interfaces. It is an auxiliary telemetry device, not a flight-controller replacement; gateway firmware and data services are not included.
- ESP32-C6FH4 MCU with integrated Wi-Fi radio and a U.FL RF connector path. - TCAN332 3.3 V CAN transceiver with NUP2105L CAN-line protection. - A fitted 120 ohm resistor across CANH and CANL. - Four-position JST GH CAN connector with VBUS…

Main components on the ESP32C6-CAN
ESP32C6-CAN bill of materials (BOM)
57 components, 33 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C6FH4 | QFN50P500X500X90-33N | U1 |
| 1 | TC2014-3.3VxCTTR | SOT-23-5 | U2 |
| 1 | TCAN332 | TSOT-23-8 | U3 |
| 1 | 74LVC1G125 | SOT-23-5 | U4 |
| 1 | 40MHz | Crystal_SMD_0603-4Pin_6.0x3.5mm | Y1 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | Micro_SD_Card | microSD_HC_Wuerth_693072010801 | J2 |
| 1 | CAN | JST_GH_SM04B-GHS-TB_1x04-1MP_P1.25mm_Horizontal | J3 |
| 1 | UART Telemetry | JST_GH_SM04B-GHS-TB_1x04-1MP_P1.25mm_Horizontal | J4 |
| 1 | I2C Connector | JST_GH_SM04B-GHS-TB_1x04-1MP_P1.25mm_Horizontal | J5 |
| 1 | SPI Connector | JST_GH_SM06B-GHS-TB_1x06-1MP_P1.25mm_Horizontal | J6 |
| 1 | KH5220-A36 | U.FL_Molex_MCRF_73412-0110_Vertical | AE2 |
| 2 | SKTAAAE010 | SW_SPST_TS-1088-xR025 | SW1, SW2 |
| 1 | RED | LED_0603_1608Metric | D1 |
| 1 | SZESD9B5.0ST5G | D_SOD-923 | D2 |
| 1 | NUP2105L | SOT-23 | D3 |
| 1 | BLUE_Activity | LED_0603_1608Metric | D4 |
| 1 | RED_ERROR | LED_0603_1608Metric | D5 |
| 1 | 2.0nH | L_0402_1005Metric | L1 |
| 1 | 3nH | L_0402_1005Metric | L2 |
Show 13 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 10uF | C_0402_1005Metric | C1, C14, C16, C17 |
| 3 | 1uF | C_0402_1005Metric | C2, C5, C13 |
| 5 | 100nF | C_0402_1005Metric | C3, C4, C9, C10, C18 |
| 1 | 10nF | C_0402_1005Metric | C6 |
| 3 | 15pF | C_0402_1005Metric | C7, C8, C15 |
| 1 | 2.4pF | C_0402_1005Metric | C11 |
| 1 | 2.2pF | C_0402_1005Metric | C12 |
| 4 | 0 | R_0402_1005Metric | R1, R2, R3, R4 |
| 3 | 5.1k | R_0402_1005Metric | R5, R9, R10 |
| 5 | 10K | R_0402_1005Metric | R6, R7, R13, R14, R15 |
| 3 | 1.5K | R_0603_1608Metric | R8, R17, R18 |
| 2 | 22R | R_0402_1005Metric | R11, R12 |
| 1 | 120R | R_0402_1005Metric | R16 |
ESP32C6-CAN design files
The KiCad project lives in the vk-sahni/ESP32C6-CAN repository on GitHub; these links point at the commit this page was built from.
- LayoutESP32-C6FH4.kicad_pcb
- SchematicESP32-C6FH4.kicad_sch
- BOMproduct.md
ESP32C6-CAN: common questions
What microcontroller does the ESP32C6-CAN use?
The ESP32C6-CAN is built around the ESP32-C6FH4, from the ESP32 family.
How big is the ESP32C6-CAN PCB?
The ESP32C6-CAN measures 40 × 25 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the ESP32C6-CAN?
57 components, from 33 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESP32C6-CAN design files?
From the vk-sahni/ESP32C6-CAN repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ESP32C6-CAN design in my own project?
The repository has no license, so all rights stay with vk-sahni. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP32C6-CAN without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k