36 open source boards using the 74LVC1G125
Real designs built with the 74LVC1G125, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
ESP-32 WLED-Controller
der-pw
59.5 × 31.2 mm19 parts2LNo license29MSI001
ATmega8
99 × 69 mm168 parts2LMIT25NextCuboid
mattuna15
214 × 142 mm27 parts4LMIT19RP2040/RP2350
RaspberryPi-Pico-Motor-Expansion-Board
eamars
91.7 × 66.8 mm63 parts4LGPL-3.018ESP32
Hardware
vivian-ng
99.5 × 99.5 mm128 parts2LNo license8CFT Processor Board 0
alexiosc
233.4 × 280 mm274 parts2LGPL-3.06ESP32
SenseEHajo
ehajo
141 × 56.9 mm97 parts2LNo license5FPGA
AmigaPCI-LBC040
AmigaPCI
159.5 × 96.5 mm124 parts6LNo license3ESP32
Hackerhotel-2024-hardware
badgeteam
90.4 × 114 mm112 parts2LCERN-OHL-P-2.03TI MSP430/CC
Projet Sound Bar DIY
HodearS
165.7 × 85 mm799 parts4LNo license2STM32
RFB
Penta0308
48.2 × 50 mm226 parts6LNo license2RP2040/RP2350
RaspberryPi-Uno
NeilKhera
68.6 × 53.3 mm62 parts2LCustom license2RP2040/RP2350
Solarpump
rivimey
100 × 160 mm424 parts4LNo license1Bifrost
YashKarthik
20 × 49.4 mm59 parts4LNo license1M5stack board unitree brushless digital servo
kim-xps12
50 × 35 mm24 parts2LMIT1ESP32
MOST25-to-AUDIO
Oleg-mk
98 × 60 mm174 parts4LCERN-OHL-S-2.00AVR/Arduino
Skin optoelectronics module
Roboy
20.6 × 6 mm77 parts4LNo license0ESP32
ESP32C6-CAN
vk-sahni
40 × 25 mm57 parts4LNo license0JLR-MOST-Reader
Oleg-mk
84.9 × 26.5 mm56 parts2LCERN-OHL-S-2.00Mouse lick detection
iBehave-eLab
56.5 × 57.5 mm33 parts2LMIT0STM32
Space noise o meter
moraszk
30 × 30 mm33 parts2LAGPL-3.00Glowprism pipe
dannyandreev
35 × 35 mm27 parts2LNo license0AVR/Arduino
Hrem
bazhenov
80 × 44.5 mm25 parts2LMIT0Breadboard midi
mprosk
45.7 × 31.8 mm14 parts2LNo license0- schematic only · 72 partsRP2040/RP2350
Ece455
ethanewer
72 partsNo license0 RISC-V
ESP32 K210
ATmega8
68.8 × 53.6 mm87 parts4LMIT25NextCuboid quilter
mattuna15
214 × 142 mm27 parts4LMIT19RP2040/RP2350
Audio player
Vaaarad07
74 × 63.1 mm84 parts2LMIT10STM32
Isometria-75-pcb iso
BenjaminJAnderson
308.3 × 123 mm320 parts2LNo license1ESP32
Jlr most amp
Oleg-mk
120.1 × 58.6 mm147 parts4LCERN-OHL-S-2.01AVR/Arduino
Mainboard
LOEWE-emergenCITY
100 × 100 mm36 parts2LNo license1NXP
MusicBrain SPI-busboard v2
MarkWestbroek
200 × 115 mm88 parts2LMIT0AVR/Arduino
Soil sensor kicad tht
ArtoLabs
22.5 × 88.1 mm29 parts2LMIT3Open MOtor DRiver Initiative (OMODRI) - Extension Board
open-dynamic-robot-initiative
50 × 50 mm167 parts6LBSD-3-Clause122STM32
Arduino can bus shield canbus custom
SamsonChau
53.3 × 56.4 mm47 parts2LNo license0MusicBrain GATEIN8 - 8x gate in slot card
MarkWestbroek
50 × 45 mm32 parts2LMIT0
How designs wire the 74LVC1G125
Read from the KiCad layouts of 32 open source designs, one per repository: what each pin of the 74LVC1G125 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 20 of 32 designs, most often 100 nF (then 1 µF).
- The C1+ pin is tied to GND on 20 of 32 designs (a signal on 12).
- The Y pin has a series resistor on 14 of 32 designs, most often 49.9 Ω (then 220 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| C1+pin 1 | Connected to: GND 63% · a signal 38% | — |
| GNDpin 3 | Connected to: GND 97% | — |
| Ypin 4 | Connected to: Signal 97% |
|
| VCCpin 5 | Connected to: 3.3V 91% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Open MOtor DRiver Initiative (OMODRI) - Extension Board by open-dynamic-robot-initiative, ESP-32 WLED-Controller by der-pw, ESP32 K210 by ATmega8 and NextCuboid by mattuna15.
The 74LVC1G125 in open source designs
The gallery holds 36 open source boards using the 74LVC1G125 from 33 GitHub repositories; a typical one measures about 80 × 57.5 mm and carries around 68 components.
60% are two-layer designs, the rest use four layers or more, and 53% carry an open source license.
The most starred is Open MOtor DRiver Initiative (OMODRI) - Extension Board by open-dynamic-robot-initiative.
Parts used alongside the 74LVC1G125
Microcontrollers on boards using the 74LVC1G125
What boards using the 74LVC1G125 are built for
74LVC1G125: common questions
Where can I find a 74LVC1G125 reference design?
Each of the 36 boards on this page is a real design using the 74LVC1G125. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the 74LVC1G125 VCC pin?
The VCC pin has a decoupling capacitor on 20 of 32 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 32 open source designs using the 74LVC1G125.
How is the 74LVC1G125 C1+ pin connected?
The C1+ pin is tied to GND on 20 of 32 designs (a signal on 12). Counted from the KiCad layouts of 32 open source designs using the 74LVC1G125.
What resistor goes on the 74LVC1G125 Y pin?
The Y pin has a series resistor on 14 of 32 designs, most often 49.9 Ω (then 220 Ω). Counted from the KiCad layouts of 32 open source designs using the 74LVC1G125.
What parts are used alongside the 74LVC1G125?
The AMS1117-3.3, AP2112K-3.3, RP2040, TPS7B8133DRV and 74LVC1G123 appear in the most repositories here.
Which microcontrollers do boards using the 74LVC1G125 use?
Most are built on ESP32 (7), RP2040/RP2350 (5), STM32 (4) and AVR/Arduino (4).
How big is a typical board using the 74LVC1G125?
The median is 80 × 57.5 mm, and 60% are two-layer designs.
What is the most popular open source board using the 74LVC1G125?
By GitHub stars, Open MOtor DRiver Initiative (OMODRI) - Extension Board by open-dynamic-robot-initiative, with 122 stars.
Can I simulate one of these boards using the 74LVC1G125 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.