Esp32-mini lab
vmcruz·esp32-mini-lab·Hardware/KiCad/ESP32-SD-Device.kicad_pcb
About the Esp32-mini lab PCB
Esp32-mini lab is an open source ESP32 PCB design by vmcruz, published on GitHub. It is a 4-layer board measuring 33.1 × 32.6 mm, with 23 components from 15 distinct parts.
Its main chip is the ESP32-C3-MINI-1, from the ESP32 family. Other key parts include the USBLC6-2SC6 and AP2112K-3.3. By type, the board carries 9 resistors, 7 capacitors, 3 ICs, 2 switches, 1 connector and 1 diode.
From the project
A compact, portable ESP32-C3 development device built from a custom-designed PCB and a 3D-printed enclosure
The following table maps the ESP32-C3 GPIOs to their corresponding signal names in the hardware design.
\*Notice: GPIO2 is connected to 3.3 V through an external 10 kΩ pull-up resistor (R9), which can be removed if needed for a different GPIO configuration.
Note: Signal names identify the nets in the hardware design; they do not restrict how the GPIOs may be used in other projects. The CS, MOSI, MISO, and SCK signals are not individually labeled on the PCB silkscreen.

Main components on the Esp32-mini lab
Esp32-mini lab bill of materials (BOM)
23 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2SC6 | SOT-23-6 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | ESP32-C3-MINI-1 | ESP32-C3-MINI-1 | U3 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | EN | SW_SPST_B3U-1000P | SW1 |
| 1 | BOOT | SW_SPST_B3U-1000P | SW2 |
| 1 | PESD5V0L1ULD | D_SOD-882D | D1 |
| 4 | 4u7 | C_0805_2012Metric | C1, C2, C3, C4 |
| 1 | 10u | C_0805_2012Metric | C5 |
| 1 | 100n | C_01005_0402Metric | C6 |
| 1 | 1u | C_0805_2012Metric | C7 |
| 2 | 5k1 | R_0402_1005Metric | R1, R2 |
| 2 | 33R | R_0805_2012Metric | R3, R6 |
| 4 | 10k | R_0402_1005Metric | R4, R5, R8, R9 |
| 1 | 0R | R_0805_2012Metric | R7 |
Esp32-mini lab design files
The KiCad project lives in the vmcruz/esp32-mini-lab repository on GitHub; these links point at the commit this page was built from.
Esp32-mini lab: common questions
What microcontroller does the Esp32-mini lab use?
The Esp32-mini lab is built around the ESP32-C3-MINI-1, from the ESP32 family.
How big is the Esp32-mini lab PCB?
The Esp32-mini lab measures 33.1 × 32.6 mm, has 4 copper layers and is 1 mm thick.
How many components are on the Esp32-mini lab?
23 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32-mini lab design files?
From the vmcruz/esp32-mini-lab repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp32-mini lab design in my own project?
The repository has no license, so all rights stay with vmcruz. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32-mini lab without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k