CubeBuddy
Volcar144·CubeBuddy
About the CubeBuddy PCB
CubeBuddy is an open source ESP32 PCB design by Volcar144, published on GitHub. It is a 2-layer board measuring 80 × 62.5 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
From the project
A PCB - pet-buddy thing produced by following the Week1 half life guide
\# CubeBuddy This is a PCB / Hardware project designed as the week 1 submission for hack-club half-life challenge.
Main components on the CubeBuddy
CubeBuddy bill of materials (BOM)
7 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U1 |
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C6-DIP | U2 |
| 1 | CONN_01X04_PIN Conn_01x04_Pin | DIP-20_W7.62mm | J1 |
| 1 | CONN_01X08_PIN Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J3 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10K 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
CubeBuddy design files
The KiCad project lives in the Volcar144/CubeBuddy repository on GitHub; these links point at the commit this page was built from.
- Layoutstarbie.kicad_pcb
- Schematicstarbie.kicad_sch
- BOMBOM.csv
CubeBuddy: common questions
What microcontroller does the CubeBuddy use?
The CubeBuddy is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the CubeBuddy PCB?
The CubeBuddy measures 80 × 62.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the CubeBuddy?
7 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the CubeBuddy design files?
From the Volcar144/CubeBuddy repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the CubeBuddy design in my own project?
The repository has no license, so all rights stay with Volcar144. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the CubeBuddy without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k