CHeepCore-HandSolder

VollstaendigerName·CHeepCore-HandSolder·CHeepCore-HandSolder/CHeepCoreHS.kicad_pcb

CHeepCore-HandSolder PCB layout, top view — open source RISC-V board by VollstaendigerName

About the CHeepCore-HandSolder PCB

CHeepCore-HandSolder is an open source RISC-V PCB design by VollstaendigerName, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 32 × 18.3 mm, with 15 components from 11 distinct parts.

Its main chip is the CH32V003FXPX, from the RISC-V family. Other key parts include the 3V3 LDO. By type, the board carries 5 connectors, 5 capacitors, 2 ICs, 2 resistors and 1 crystal.

It belongs with the dev boards & breakouts and usb & debug tools designs in this gallery.

From the project

CHeepCore is a minimalist, ultra-low-cost RISC-V development board built around the CH32V003F4P6 microcontroller. It exposes 16 GPIOs on breadboard-compatible headers, features USB-C power with selectable 3.3 V/5 V rails, and supports SWD/JTAG programming, all for under 0.50€.

- Name: CHeepCore-HandSolder - Revision: 0.0.1b - Date: 2025-08-06 - KiCad Version: 9.0.3 - Target Audience: Embedded hobbyists, students, low-cost prototyping - Cost Goal: Complete microcontroller board for under 0.50€

- CH32V003F4U6 32-bit RISC-V microcontroller (20-pin QFN) - 16 GPIOs exposed on 2.54 mm headers (PC0–PC7, PD0–PD7) - External 24 MHz crystal with 22 pF load capacitors - USB-C power input (VBUS → 3.3 V LDO) - Configurable solder jumpers for: - USB-VBUS disconnect - 3.3 V / 5 V MCU supply - SWD/JTAG programming connectors (3-pin & 10-pin, WCH-LinkE compatible) -…

CHeepCore-HandSolder, from the project README
From the project README

Main components on the CHeepCore-HandSolder

CHeepCore-HandSolder bill of materials (BOM)

15 components, 11 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
CH32V003FXPX
CH32V003FxPx
U101
1
3V3 LDO
U301
1
CRYSTAL_GND24
Crystal_GND24
Y101
2
CONN_01X10
Conn_01x10
J101, J102
1
USB
J103
1
CONN_01X03
Conn_01x03
J201
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J301
1
100NF
100nF
C101
2
22PF
22pF
C102, C103
2
1µF
C301, C302
2
5K1
5k1
R301, R302

CHeepCore-HandSolder design files

The KiCad project lives in the VollstaendigerName/CHeepCore-HandSolder repository on GitHub; these links point at the commit this page was built from.

CHeepCore-HandSolder: common questions

What microcontroller does the CHeepCore-HandSolder use?

The CHeepCore-HandSolder is built around the CH32V003FXPX, from the RISC-V family.

How big is the CHeepCore-HandSolder PCB?

The CHeepCore-HandSolder measures 32 × 18.3 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the CHeepCore-HandSolder?

15 components, from 11 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the CHeepCore-HandSolder design files?

From the VollstaendigerName/CHeepCore-HandSolder repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the CHeepCore-HandSolder design in my own project?

It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.

Can I test firmware for the CHeepCore-HandSolder without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RISC-V firmware against it before you order a PCB.

Similar boards