8 open source boards using the 3V3-LDO
Real designs built with the 3V3-LDO, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PistormTester
abrugsch
99.8 × 99.8 mm92 parts2LNo license11ESP32
Capable jetson carrier
CapableRobot
100 × 55 mm344 parts6LApache-2.00RISC-V
CHeepCore-HandSolder
VollstaendigerName
32 × 18.3 mm15 parts2LCC-BY-NC-4.00RISC-V
CHeepCore
VollstaendigerName
29.5 × 18.3 mm15 parts2LCC-BY-NC-4.00ESP32
CRMHJN capable carrier
CapableRobot
122 × 77 mm344 parts6LApache-2.00ESP32
Mesh phone
JeremyLakeyJr
87 × 154 mm95 parts2LNo license0ESP32
Owasso1-before rf ground finish
JeremyLakeyJr
87 × 154 mm95 parts2LNo license0ESP32
Owasso1-unrouted
JeremyLakeyJr
87 × 154 mm95 parts2LNo license0
How designs wire the 3V3-LDO
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the 3V3-LDO connects to, and the resistors, capacitors and other passives placed on it.
- The VO pin has a decoupling capacitor on 3 of 5 designs, most often 1 µF (then 100 nF).
- The VI pin has a decoupling capacitor on 3 of 5 designs, most often 1 µF.
- Pin 4 is left unconnected on 2 of 2 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 60% · 5V 40% | — |
| VOpin 2 | Connected to: 3.3V 60% · GND 40% |
|
| VIpin 3 | Connected to: 5V 60% · not connected 20% · a signal 20% |
|
| Pin 4 | Connected to: Not connected 100% | — |
| VOUTpin 5 | Connected to: 3.3V 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PistormTester by abrugsch, Capable jetson carrier by CapableRobot, Mesh phone by JeremyLakeyJr and CHeepCore by VollstaendigerName.
The 3V3-LDO in open source designs
The gallery holds 8 open source boards using the 3V3-LDO from 5 GitHub repositories; a typical one measures about 87 × 88.4 mm and carries around 95 components.
75% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is PistormTester by abrugsch.
What boards using the 3V3-LDO are built for
3V3-LDO: common questions
Where can I find a 3V3-LDO reference design?
Each of the 8 boards on this page is a real design using the 3V3-LDO. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the 3V3-LDO VO pin?
The VO pin has a decoupling capacitor on 3 of 5 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the 3V3-LDO.
What decoupling capacitors do designs use on the 3V3-LDO VI pin?
The VI pin has a decoupling capacitor on 3 of 5 designs, most often 1 µF. Counted from the KiCad layouts of 5 open source designs using the 3V3-LDO.
How is the 3V3-LDO pin 4 connected?
Pin 4 is left unconnected on 2 of 2 designs. Counted from the KiCad layouts of 5 open source designs using the 3V3-LDO.
Which microcontrollers do boards using the 3V3-LDO use?
Most are built on ESP32 (5) and RISC-V (2).
How big is a typical board using the 3V3-LDO?
The median is 87 × 88.4 mm, and 75% are two-layer designs.
What is the most popular open source board using the 3V3-LDO?
By GitHub stars, PistormTester by abrugsch, with 11 stars.
Can I simulate one of these boards using the 3V3-LDO before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.