RPiLinearServo
vsi5004·RPiLinearServo·PCB/RPiLinearServo.kicad_pcb
About the RPiLinearServo PCB
RPiLinearServo is an open source RP2040/RP2350 PCB design by vsi5004, published on GitHub under the MIT license. It is a 2-layer board measuring 42.3 × 30.3 mm, with 16 components from 12 distinct parts.
Its main chip is the RP2040-ZERO, from the RP2040/RP2350 family. Other key parts include the TMC2209_SILENTSTEPSTICK, DRV5055A3XDBZXQ1 and 74LVC1G17. By type, the board carries 6 capacitors, 4 ICs, 3 resistors, 2 connectors and 1 diode.
It belongs with the robotics & motion designs in this gallery.
From the project
KiCad schematic and PCB design files for the RPiLinearServo controller board.
KiCad schematic and PCB design files for the RPiLinearServo controller board.
The 1 kΩ series resistor (R1) between GP4 and the TMC2209 PDN/UART pin provides signal isolation so the driver can pull the bus low during reply frames without fighting the RP2040 TX output. GP4 is tri-stated after each write to allow the TMC2209 to respond over the half-duplex bus.
Main components on the RPiLinearServo
RPiLinearServo bill of materials (BOM)
16 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TMC2209_SILENTSTEPSTICK | MODULE_TMC2209_SILENTSTEPSTICK | U1 |
| 1 | RP2040-ZERO | MODULE_RP2040-ZERO | U2 |
| 1 | DRV5055A3XDBZXQ1 DRV5055A3xDBZxQ1 | SOT-23_Handsoldering | U3 |
| 1 | 74LVC1G17 | SOT-23-5_HandSoldering | U4 |
| 1 | CONN_01X03_PIN Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | CONN_02X02_ODD_EVEN Conn_02x02_Odd_Even | PinHeader_2x02_P2.54mm_Vertical | J2 |
| 1 | TPD1E10B06DPYR | D_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D1 |
| 2 | EEEFPC101XAP | CAP_EEEFPC101XAP | C1, C3 |
| 2 | 2.2UF 2.2uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C5 |
| 2 | 0.1UF 0.1uF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C4, C6 |
| 2 | 1K | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 1 | 330 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
RPiLinearServo design files
The KiCad project lives in the vsi5004/RPiLinearServo repository on GitHub; these links point at the commit this page was built from.
RPiLinearServo: common questions
What microcontroller does the RPiLinearServo use?
The RPiLinearServo is built around the RP2040-ZERO, from the RP2040/RP2350 family.
How big is the RPiLinearServo PCB?
The RPiLinearServo measures 42.3 × 30.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the RPiLinearServo?
16 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the RPiLinearServo design files?
From the vsi5004/RPiLinearServo repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the RPiLinearServo design in my own project?
Yes, under the terms of its MIT license, which vsi5004 chose for the repository.
Can I test firmware for the RPiLinearServo without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
Similar boards
RP2040/RP2350
OSO-BOOK-C1
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1kRP2040/RP2350
Corne cherry
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Corne chocolate
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0kRP2040/RP2350
LogicAnalyzer
gusmanb
57 × 55.2 mm6 parts2LGPL-3.05.0kRP2040/RP2350
Main
google
98 × 71 mm102 parts2LApache-2.02.9k