Mach
VuongTrinhMinh·Mach
About the Mach PCB
Mach is an open source ESP32 PCB design by VuongTrinhMinh, published on GitHub. It is a 2-layer board measuring 38.6 × 54.5 mm, with 18 components from 13 distinct parts.
Its main chip is the DOIT-ESP32-DEVKIT-V1, from the ESP32 family. Other key parts include the module_mpu6050, module_max30102 and AMS1117-3.3. By type, the board carries 5 resistors, 4 ICs, 4 capacitors, 2 connectors, 2 diodes and 1 buzzer.
Main components on the Mach
Mach bill of materials (BOM)
18 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DOIT-ESP32-DEVKIT-V1 | ESP32-DOIT-DEVKIT | U1 |
| 1 | module_mpu6050 | module_mpu6050 | U2 |
| 1 | module_max30102 | module_max30102 | U4 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U5 |
| 1 | Conn_01x02_Pin | JST_SH_SM02B-SRSS-TB_1x02-1MP_P1.00mm_Horizontal | J1 |
| 1 | Conn_01x06_Pin | TP4056-18650 | J2 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 2 | LED | LED_0805_2012Metric | D1, D2 |
| 2 | 100nF | C_0805_2012Metric | C1, C3 |
| 2 | 10uF | C_0805_2012Metric | C2, C4 |
| 2 | 4k7 | R_0805_2012Metric | R1, R2 |
| 2 | 1k | R_0805_2012Metric | R3, R4 |
| 1 | R | R_0805_2012Metric | R5 |
Mach design files
The KiCad project lives in the VuongTrinhMinh/Mach repository on GitHub; these links point at the commit this page was built from.
- LayoutMach.kicad_pcb
- SchematicMach.kicad_sch
Mach: common questions
What microcontroller does the Mach use?
The Mach is built around the DOIT-ESP32-DEVKIT-V1, from the ESP32 family.
How big is the Mach PCB?
The Mach measures 38.6 × 54.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Mach?
18 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Mach design files?
From the VuongTrinhMinh/Mach repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Mach design in my own project?
The repository has no license, so all rights stay with VuongTrinhMinh. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Mach without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k