Eth camera
wouldgo·eth-camera·hardware/eth-camera.kicad_sch
About the Eth camera PCB
Eth camera is an open source ESP32 PCB design by wouldgo, published on GitHub. It is a board, with 11 components from 8 distinct parts.
Its main chip is the ESP32-CAM, from the ESP32 family. Other key parts include the USR-ES1. By type, the board carries 3 test points, 2 ICs, 2 switches, 2 capacitors and 1 connector.
From the project
An ESP32-CAM project that exposes a camera snapshot over HTTP via a wired Ethernet connection (W5500 SPI module). The device also blinks status messages in Morse code on a dedicated LED.
An ESP32-CAM project that exposes a camera snapshot over HTTP via a wired Ethernet connection (W5500 SPI module). The device also blinks status messages in Morse code on a dedicated LED.
The firmware runs on an ESP32-CAM (AI-Thinker) board and uses a W5500 SPI-to-Ethernet chip to get a wired network connection. On boot it:
1. Blinks the flash LED to signal it is starting up. 2. Initialises Ethernet. DHCP runs in the background: boot does not wait for an IP address. 3. Initialises the OV2640 camera sensor. 4. Starts an HTTP server on port 3000. 5. Every 30 s blinks the last octet of its IP…
Main components on the Eth camera
Eth camera bill of materials (BOM)
11 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USR-ES1 W5500 | USRES1_W_HEADERS | IC1 |
| 1 | ESP32-CAM | ESP32-CAM_W_HEADERS | U1 |
| 1 | Conn_01x02_Socket | PinSocket_1x02_P2.54mm_Vertical | J1 |
| 1 | SKHLAAA010 | SKHLAAA010 | B1 |
| 2 | SS-12D00-G 4 E | 1P2T_SS-12D00_CNK | SW1, SW2 |
| 3 | TestPoint | PinSocket_1x01_P2.54mm_Vertical | TP1, TP2, TP3 |
| 1 | 470uF 25v | CP_Radial_D10.0mm_P5.00mm | C1 |
| 1 | 100nF | C_Disc_D4.7mm_W2.5mm_P5.00mm | C2 |
Eth camera design files
The KiCad project lives in the wouldgo/eth-camera repository on GitHub; these links point at the commit this page was built from.
- Schematichardware/eth-camera.kicad_sch
- BOMREADME.md
Eth camera: common questions
What microcontroller does the Eth camera use?
The Eth camera is built around the ESP32-CAM, from the ESP32 family.
How many components are on the Eth camera?
11 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Eth camera design files?
From the wouldgo/eth-camera repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Eth camera design in my own project?
The repository has no license, so all rights stay with wouldgo. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Eth camera without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k