Blindspot
wroug·blindspot·PCB/BL1NDSP0T.kicad_pcb
About the Blindspot PCB
Blindspot is an open source RP2040/RP2350 PCB design by wroug, published on GitHub. It is a 4-layer board measuring 39.4 × 18.6 mm, with 44 components from 18 distinct parts.
Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the W25Q32JVSS, AP2112K-3.3, USBLC6-2SC6 and MAX3421EETJ_. By type, the board carries 25 capacitors, 6 ICs, 6 resistors, 2 crystals, 2 connectors and 2 diodes.
From the project
A hardware USB keylogger
1. Solder each component to it's respective pads (reference the BOM)
2. Put the pcb in the bottom half of the case.
3. Screw it to the case using 2x M2x4mm screws at these points.
4. Cover it with the top half of the case, making sure the extrusions insert nicely into the slots.
5. Secure the assembly together with a M2x8mm screw at the bottom
!! FLASHING INSTRUCTIONS NOT INCLUDED AS THE FIRMWARE IS NOT FINISHED.
Main components on the Blindspot
Blindspot bill of materials (BOM)
44 components, 18 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RP2040 | QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | W25Q32JVSS | SOIC-8_5.3x5.3mm_P1.27mm | U2 |
| 1 | AP2112K-3.3 | SOT-23-5 | U3 |
| 2 | USBLC6-2SC6 | SOT-23-6 | U4, U6 |
| 1 | MAX3421EETJ_ | 21-0140L_T3255-4_MXM | U5 |
| 2 | 12MHZ 12MHz | Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y1, Y2 |
| 1 | USB_A_MALE | CONN_480370001_MOL | J2 |
| 1 | USB_A_FEMALE | CONN4_292303_TEC | J3 |
| 1 | Jumper_2_Open | SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
| 1 | BLUE | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | ORANGE | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 13 | 100NF 100nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C11, C15, C16, C17, C18, C19 +5 |
| 7 | 1UF 1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C5, C6, C12, C25, C26 |
| 4 | 27PF 27pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C8, C9, C10 |
| 1 | 10UF 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C27 |
| 2 | 33R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 2 | 27R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4 |
| 2 | 10K 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R6 |
Blindspot design files
The KiCad project lives in the wroug/blindspot repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/BL1NDSP0T.kicad_pcb
- SchematicPCB/BL1NDSP0T.kicad_sch
- BOMPCB/BOM.csv
Blindspot: common questions
What microcontroller does the Blindspot use?
The Blindspot is built around the RP2040, from the RP2040/RP2350 family.
How big is the Blindspot PCB?
The Blindspot measures 39.4 × 18.6 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Blindspot?
44 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Blindspot design files?
From the wroug/blindspot repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Blindspot design in my own project?
The repository has no license, so all rights stay with wroug. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Blindspot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
Similar boards
RP2040/RP2350
OSO-BOOK-C1
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1kRP2040/RP2350
Corne cherry
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Corne chocolate
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0kRP2040/RP2350
LogicAnalyzer
gusmanb
57 × 55.2 mm6 parts2LGPL-3.05.0kRP2040/RP2350
Main
google
98 × 71 mm102 parts2LApache-2.02.9k