Bebl v2 main
About the Bebl v2 main PCB
Bebl v2 main is an open source AVR/Arduino PCB design by wyolum, published on GitHub. It is a 2-layer board measuring 80 × 24 mm, with 51 components from 29 distinct parts.
Its main chip is the ATMEGA328, from the AVR/Arduino family. Other key parts include the MCP73831, TPS61221DCK and ADXL345. By type, the board carries 11 capacitors, 9 connectors, 6 resistors, 4 ICs, 2 switches and 1 crystal.
From the project
"Bar End Brake Light" , redux. v2 of Justin's original BEBL with mods.
"Bar End Brake Light" , redux. v2 of Justin's original BEBL with mods.
[CERN Open Hardware Licence v1.2 ]:http://www.ohwr.org/attachments/2388/cernohlv12.txt
Main components on the Bebl v2 main
Bebl v2 main bill of materials (BOM)
51 components, 29 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATMEGA328 | TQFP32 | U1 |
| 1 | MCP73831 | SOT23-5 | U2 |
| 1 | TPS61221DCK | SOT23-6_LDO | U3 |
| 1 | ADXL345 | ADXL345 | U4 |
| 1 | 8MHz | Xtal_SMD4 | X1 |
| 1 | ISP | Header_3x2_ISP | P1 |
| 1 | FTDI | PIN_ARRAY-6X1 | P2 |
| 1 | LED_1 | pin_socket_2 | P3 |
| 1 | LED_2 | pin_socket_2 | P4 |
| 1 | LED_3 | pin_socket_2 | P5 |
| 1 | LED_PWR | pin_socket_2 | P6 |
| 1 | USB-Micro | USB_B_Micro_seeed | P7 |
| 1 | CHG_LED | pin_socket_2 | P8 |
| 1 | Ext_LiPo | pin_socket_2 | P9 |
| 7 | I/O | breakout_smd | B1, B2, B3, B4, B5, B6, B7 |
| 1 | LiPo+ | batt_clip | B8 |
| 1 | LiPo- | batt_clip | B9 |
| 8 | SCREW | screw_3mm | SC1, SC2, SC3, SC4, SC5, SC6, SC7, SC8 |
| 1 | RST | Switch_SMT | SW1 |
| 1 | MODE | Switch_SMT | SW2 |
Show 9 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 4u7 | Inductor_LQH3NPN | L1 |
| 2 | 22p | c_0805 | C1, C2 |
| 2 | 100n | c_0805 | C3, C4 |
| 2 | 4u7 | c_0805 | C5, C6 |
| 3 | 10uF | c_0805 | C7, C8, C9 |
| 2 | 100nF | c_0805 | C10, C11 |
| 4 | 10k | r_0805 | R1, R2, R3, R4 |
| 1 | 150E | r_0805 | R5 |
| 1 | 2k | r_0805 | R6 |
Bebl v2 main design files
The KiCad project lives in the wyolum/bebl_v2 repository on GitHub; these links point at the commit this page was built from.
Bebl v2 main: common questions
What microcontroller does the Bebl v2 main use?
The Bebl v2 main is built around the ATMEGA328, from the AVR/Arduino family.
How big is the Bebl v2 main PCB?
The Bebl v2 main measures 80 × 24 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Bebl v2 main?
51 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Bebl v2 main design files?
From the wyolum/bebl_v2 repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Bebl v2 main design in my own project?
The repository has no license, so all rights stay with wyolum. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Bebl v2 main without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in bebl_v2
Similar boards
AVR/ArduinoMagspoof
samyk
35 × 29 mm11 parts2LNo license4.2k
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoLabrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2k
AVR/ArduinoV4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoModuleV450
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k