Hava
yavuzselimuyaner·hava-istasyonu·pcb/main/hava.kicad_pcb
About the Hava PCB
Hava is an open source ESP32 PCB design by yavuzselimuyaner, published on GitHub. It is a 2-layer board measuring 32 × 41 mm, with 22 components from 14 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the AP2112K-3.3 and USBLC6-2SC6. By type, the board carries 9 resistors, 5 capacitors, 3 ICs, 2 connectors, 2 switches and 1 diode.
It belongs with the iot & wireless and sensors designs in this gallery.
From the project
ESP32-C3 hava istasyonu: kart (KiCad), firmware (ESP-IDF), kutu (FreeCAD) - LLM destekli tasarim sureci
A device that measures outdoor temperature, humidity and pressure, publishes the readings to the internet over Wi-Fi, and shows them on a browser page.
- Main board: ESP32-C3 (Wi-Fi processor module), USB-C, 3.3 V regulator, reset and boot buttons, status LED, and a 4-pin connector for the sensor. Held in the enclosure with two M2 screws. - Sensor board: BME280 (temperature, humidity, pressure) and a connector. It is separate from the main board and connected by a cable, because the processor and regulator warm up and a sensor next to them would read the temperature too high. - Design…

Main components on the Hava
Hava bill of materials (BOM)
22 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U4 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | Conn_01x04 | PinHeader_1x04_P2.54mm_Horizontal | J2 |
| 2 | SW_Push | SW_SPST_B3U-1000P | SW1, SW2 |
| 1 | LED | LED_0603_1608Metric | D1 |
| 3 | 10uF | C_0805_2012Metric | C1, C2, C3 |
| 1 | 100nF | C_0402_1005Metric | C4 |
| 1 | 1uF | C_0402_1005Metric | C5 |
| 2 | 5.1k | R_0402_1005Metric | R1, R2 |
| 4 | 10k | R_0402_1005Metric | R3, R4, R8, R9 |
| 2 | 4.7k | R_0402_1005Metric | R5, R6 |
| 1 | 1k | R_0402_1005Metric | R7 |
Hava design files
The KiCad project lives in the yavuzselimuyaner/hava-istasyonu repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/main/hava.kicad_pcb
- Schematicpcb/main/hava.kicad_sch
Hava: common questions
What microcontroller does the Hava use?
The Hava is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the Hava PCB?
The Hava measures 32 × 41 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Hava?
22 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Hava design files?
From the yavuzselimuyaner/hava-istasyonu repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Hava design in my own project?
The repository has no license, so all rights stay with yavuzselimuyaner. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Hava without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in hava-istasyonu
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k