NadiSense
yeswantsakthi-hub·NadiSense·electronics/ring_v2_revB/NadiSense_ring_v2_revB.kicad_pcb
About the NadiSense PCB
NadiSense is an open source Nordic nRF PCB design by yeswantsakthi-hub, published on GitHub. It is a 2-layer board measuring 66.8 × 6 mm, with 48 components from 32 distinct parts.
Its main chip is the NRF52840-CKAA, from the Nordic nRF family. Other key parts include the MAX86141ENP+, TMP117AIDRVR, LIS2DW12TR and BQ25120AYFPR. By type, the board carries 22 capacitors, 6 test points, 6 resistors, 5 ICs, 3 diodes and 2 inductors.
It belongs with the power & battery designs in this gallery.
From the project
NadiSense smart ring for overnight pulse-based screening. Vishwakarma Awards 2026-27 (VK26-AU-FD-0015): CAD, FEA, KiCad schematic, power budget.
Rev B replaces the Stage 2 simplified schematic (../kicad/) and the Rev A layout study. Every IC now uses its manufacturer pin / ball map and the support parts its data sheet calls for, and the flex PCB is routed against those real footprints.
The BQ25120A buck output (SYS) is the single 1.8 V rail for every IC. The nRF52840 runs in normal-voltage mode (VDD = VDDH = 1.8 V, internal LDOs), so no 3.3 V rail is needed. The LEDs run from VBAT through the MAX86141 drivers. The Stage 2 deck and report describe a 3.3 V buck feeding the nRF52840 regulator; Rev B simplifies this.

Main components on the NadiSense
NadiSense bill of materials (BOM)
48 components, 32 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NRF52840-CKAA nRF52840-CKAA | Nordic_WLCSP-94_3.544x3.607mm_P0.35mm | U1 |
| 1 | MAX86141ENP+ | Maxim_WLP-20_2.048x1.848mm_Layout5x4_P0.4mm | U2 |
| 1 | TMP117AIDRVR | WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U3 |
| 1 | LIS2DW12TR | LGA-12_2x2mm_P0.5mm | U4 |
| 1 | BQ25120AYFPR | TI_DSBGA-25_2.5x2.5mm_Layout5x5_P0.5mm | U5 |
| 1 | 32MHz 8pF | Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1 |
| 1 | Charge pads | ChargePads_2xD1.2mm | J1 |
| 1 | 2450AT18A100 | Johanson_2450AT18x100 | AE1 |
| 1 | Li-Po 3.7V 12mAh | LiPo_Tabs_1.6x1.9mm | BT1 |
| 1 | SWDIO | TestPad_D0.8mm | TP1 |
| 1 | SWDCLK | TestPad_D0.8mm | TP2 |
| 1 | nRESET | TestPad_D0.8mm | TP3 |
| 1 | +1V8 | TestPad_D0.8mm | TP4 |
| 1 | GND | TestPad_D0.8mm | TP5 |
| 1 | MR | TestPad_D0.8mm | TP6 |
| 1 | Red 660nm | LED_0603_1608Metric | D1 |
| 1 | IR 880nm | LED_0603_1608Metric | D2 |
| 1 | Si PIN PD 2x2mm | PD_2x2mm | D3 |
| 1 | 2.2UH 2.2uH | L_0603_1608Metric | L1 |
| 1 | 3.9NH 3.9nH | L_0201_0603Metric | L2 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 7 | 100NF 100nF | C_0201_0603Metric | C1, C5, C10, C12, C15, C16, C17 |
| 3 | 1.0UF 1.0uF | C_0402_1005Metric | C2, C18, C21 |
| 1 | 47NF 47nF | C_0201_0603Metric | C3 |
| 2 | 4.7UF 4.7uF | C_0402_1005Metric | C4, C19 |
| 2 | 12PF 12pF | C_0201_0603Metric | C6, C7 |
| 1 | 0.8PF 0.8pF | C_0201_0603Metric | C8 |
| 3 | 10UF 10uF | C_0402_1005Metric | C11, C14, C20 |
| 3 | 1.0UF 1.0uF | C_0201_0603Metric | C13, C22, C23 |
| 2 | 4.7K 4.7k | R_0201_0603Metric | R1, R2 |
| 2 | 10K 10k | R_0201_0603Metric | R3, R6 |
| 1 | R_ISET | R_0201_0603Metric | R4 |
| 1 | R_IPRETERM | R_0201_0603Metric | R5 |
NadiSense design files
The KiCad project lives in the yeswantsakthi-hub/NadiSense repository on GitHub; these links point at the commit this page was built from.
NadiSense: common questions
What microcontroller does the NadiSense use?
The NadiSense is built around the NRF52840-CKAA, from the Nordic nRF family.
How big is the NadiSense PCB?
The NadiSense measures 66.8 × 6 mm, has 2 copper layers and is 0.11 mm thick.
How many components are on the NadiSense?
48 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the NadiSense design files?
From the yeswantsakthi-hub/NadiSense repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the NadiSense design in my own project?
The repository has no license, so all rights stay with yeswantsakthi-hub. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the NadiSense without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Nordic nRF firmware against it before you order a PCB.
Similar boards
Nordic nRF
Keyboard
byrantech
262.5 × 109.6 mm206 parts2LMIT4.3kNordic nRF
TOTEM
GEIGEIGEIST
258.8 × 94.4 mm85 parts2LCERN-OHL-P-2.02.0kNordic nRF
Pixl.js
solosky
40 × 23 mm45 parts4LGPL-2.01.4kNordic nRF
Management
dennisss
101 × 31.5 mm50 parts2LApache-2.0381Nordic nRF
Board
dennisss
363 × 128 mm420 parts4LApache-2.0381Nordic nRF
Board hl15-latest
dennisss
61 × 37 mm14 parts2LApache-2.0381