31 open source boards using the TMP117AIDRVR
Real designs built with the TMP117AIDRVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FourThirdsEye
will127534
47 × 47 mm106 parts4LMIT384OneInchEye
will127534
39 × 39 mm79 parts4LMIT355STM32
StarlightEye
will127534
39 × 39 mm111 parts4LMIT328AVR/Arduino
Sense debug
unsurv
65 × 40 mm44 parts4LNo license49Cellsim-8ch
atopile
13 × 9 mm608 parts4LMIT29ShutterEye
will127534
39 × 39 mm140 parts4LMIT25ESP32
Kompic Mk1b
porupski
44.5 × 50.6 mm121 parts4LGPL-3.03TMP117-ADXL345 section 5cm
BerkeleyLab
228.9 × 5.5 mm38 parts2LCustom license1Rfof frx
liuweiseu
60 × 40 mm100 parts4LCERN-OHL-S-2.00Nordic nRF
Nrf9151-modbus
mathijsmeulendijks
86 × 56 mm95 parts4LNo license0ESP32
Esp32c6-ble sensor coin cell
xmyoot
31.4 × 31 mm53 parts4LNo license0PCB-for-SiPM-characterisation
prat4002
174 × 88 mm53 parts2LNo license0Bike powermeter
Guiimartinho
50 × 16 mm51 parts4LCC-BY-NC-4.00Nordic nRF
NadiSense
yeswantsakthi-hub
66.8 × 6 mm48 parts2LNo license0Temperature Sensor I2C
ABlairJamieson
28 × 11 mm8 parts2LNo license0Raspberry Pi
CM4Card
will127534
64.6 × 44 mm54 parts4LMIT95AVR/Arduino
Pocket knife sense display
unsurv
14.8 × 38.8 mm29 parts4LNo license49ESP32
Kompic Mk1
porupski
44.5 × 50.6 mm119 parts4LGPL-3.03TMP117 section 10cm
BerkeleyLab
228.9 × 5.5 mm38 parts2LCustom license1STM32
Thermocouples
npgo22
85 × 76 mm163 parts4LNo license0FRX
EIGSEP
60 × 40 mm100 parts4LNo license0TMP117 section 5cm
BerkeleyLab
228.9 × 5.5 mm38 parts2LCustom license1AVR/Arduino
Nfc sense ntag
unsurv
18.6 × 34.5 mm17 parts4LNo license49AVR/Arduino
Nfc sense ntag panel
unsurv
121 × 87.9 mm17 parts4LNo license49AVR/Arduino
Nfc sense
unsurv
18.6 × 43.2 mm16 parts4LNo license49Nfc sense ntag surface
unsurv
18.6 × 76 mm16 parts4LNo license49AVR/Arduino
Nfc sense panel
unsurv
121 × 105.3 mm16 parts4LNo license49AVR/Arduino
Nfc sense coin
unsurv
23.3 × 26.4 mm15 parts4LNo license49Micro vault dev board
atopile
32.4 × 64.4 mm39 parts2LMIT29AVR/Arduino
Pocket knife sense
unsurv
14.8 × 38.8 mm15 parts4LNo license49ESP32
Esp32 tmp117
HeyPCB
30 × 48 mm24 parts4LCERN-OHL-S-2.00
How designs wire the TMP117AIDRVR
Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the TMP117AIDRVR connects to, and the resistors, capacitors and other passives placed on it.
- The V+ pin has a decoupling capacitor on 18 of 19 designs, most often 100 nF (then 1 µF).
- The ADD0 pin is tied to GND on 15 of 19 designs (a signal on 4).
- The SCL pin has a pull-up to 3.3V on 11 of 19 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA pin has a pull-up to 3.3V on 11 of 19 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCLpin 1 | Connected to: A connector 53%, the microcontroller 32%, TCA9406DC 21% |
|
| GNDpin 2 | Connected to: GND 95% | — |
| ADD0pin 4 | Connected to: GND 79% · a signal 21% | — |
| V+pin 5 | Connected to: 3.3V 68% · a signal 32% |
|
| SDApin 6 | Connected to: A connector 53%, the microcontroller 32%, TCA9406DC 21% |
|
| TPADpin 7 | Connected to: GND 69% · not connected 23% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include FourThirdsEye by will127534, OneInchEye by will127534, StarlightEye by will127534 and CM4Card by will127534.
The TMP117AIDRVR in open source designs
The gallery holds 31 open source boards using the TMP117AIDRVR from 19 GitHub repositories; a typical one measures about 44.5 × 40 mm and carries around 48 components.
77% use four copper layers or more, and 35% carry an open source license.
The most starred is FourThirdsEye by will127534.
Parts used alongside the TMP117AIDRVR
Microcontrollers on boards using the TMP117AIDRVR
What boards using the TMP117AIDRVR are built for
TMP117AIDRVR: common questions
Where can I find a TMP117AIDRVR reference design?
Each of the 31 boards on this page is a real design using the TMP117AIDRVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TMP117AIDRVR V+ pin?
The V+ pin has a decoupling capacitor on 18 of 19 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 19 open source designs using the TMP117AIDRVR.
How is the TMP117AIDRVR ADD0 pin connected?
The ADD0 pin is tied to GND on 15 of 19 designs (a signal on 4). Counted from the KiCad layouts of 19 open source designs using the TMP117AIDRVR.
What pull-up resistor is used on the TMP117AIDRVR SCL pin?
The SCL pin has a pull-up to 3.3V on 11 of 19 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 19 open source designs using the TMP117AIDRVR.
What parts are used alongside the TMP117AIDRVR?
The TCA9406DC, AP3418KTR-G1, ICM-42688-P, LP5907MFX-1.8 and TCA6408ARGTR appear in the most repositories here.
Which microcontrollers do boards using the TMP117AIDRVR use?
Most are built on AVR/Arduino (8), ESP32 (4), Nordic nRF (2) and STM32 (2).
How big is a typical board using the TMP117AIDRVR?
The median is 44.5 × 40 mm, and 23% are two-layer designs.
What is the most popular open source board using the TMP117AIDRVR?
By GitHub stars, FourThirdsEye by will127534, with 384 stars.
Can I simulate one of these boards using the TMP117AIDRVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.