Minidrone fc
yisikawa·minidrone_fc
About the Minidrone fc PCB
Minidrone fc is an open source ESP32 PCB design by yisikawa, published on GitHub. It is a 4-layer board measuring 50 × 64 mm, with 37 components from 16 distinct parts.
Its main chip is the XIAO_ESP32C3, from the ESP32 family. Other key parts include the GY-521, WF282A and TPS63002DRCR. By type, the board carries 12 capacitors, 10 resistors, 5 diodes, 4 ICs, 4 transistors and 1 connector.
From the project
KiCADによるdrone基板作成
1. このフォルダごと D:\KicadProjects\ などに置く(D:\Kicad の中には置かないでください。KiCad更新時に消える可能性があります) 2. minidronefc.kicadpro をダブルクリック 3. 回路図(.kicadsch`)を開く
KiCad 10で開くとファイル形式の変換確認が出ます。 このプロジェクトはKiCad 7形式で生成されているためです。 「はい」で変換してください。以後は10形式で保存されます。
U1のフットプリントは意図的に空欄にしてあります。 XIAOはKiCad公式ライブラリに含まれず、環境によってライブラリ名が 変わるため、こちらで決め打ちできませんでした。
1. https://github.com/Seeed-Studio/OPLKicadLibrary をZIPで取得 2. 展開し、Seeed Studio XIAO Series Library/ 内の .kicadsym を 設定 → シンボルライブラリを管理 から追加 3. フットプリントは .pretty フォルダに入っていないと認識されません。 単体の .kicadmod ファイルの場合は SeeedXIAO.pretty という フォルダを作って中に移動してから、 設定 → フットプリントライブラリを管理 で追加 4. 回路図でU1を選択 → E…
Main components on the Minidrone fc
Minidrone fc bill of materials (BOM)
37 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO_ESP32C3 | XIAO-ESP32-C3-DIP | U1 |
| 1 | GY-521 | PinHeader_1x08_P2.54mm_Vertical | U2 |
| 1 | WF282A BMP280 | Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U3 |
| 1 | TPS63002DRCR TPS63002 | VSON-10-1EP_3x3mm_P0.5mm_EP1.65x2.4mm_ThermalVias | U4 |
| 4 | AO3400A Alpha & Omega | SOT-23 | Q1, Q2, Q3, Q4 |
| 1 | S2B-PH-K-S(LF)(SN) BATT JST | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J1 |
| 5 | SS24 | D_SMA | D1, D2, D3, D4, D5 |
| 1 | NRS3015T2R2MNGHV 2.2uH | L_APV_ANR3015 | L1 |
| 1 | CS1A221M-CRE54 220u | CP_Elec_6.3x5.3 | C1 |
| 1 | CK1C101M-CRE54 100u | CP_Elec_6.3x5.3 | C2 |
| 8 | CC0603KRX7R9BB104 0.1u | C_0603_1608Metric | C3, C4, C5, C6, C7, C8, C9, C12 |
| 1 | 10u | C_0805_2012Metric | C10 |
| 1 | 22u | C_0805_2012Metric | C11 |
| 2 | 0603WAF1003T5E 100k | R_0603_1608Metric | R1, R2 |
| 4 | RK73H1JTTD1002F 10k | R_0603_1608Metric | R3, R4, R5, R6 |
| 4 | 0603WAF1500T5E 150 | R_0603_1608Metric | R7, R8, R9, R10 |
Minidrone fc design files
The KiCad project lives in the yisikawa/minidrone_fc repository on GitHub; these links point at the commit this page was built from.
- Layoutminidrone_fc.kicad_pcb
- Schematicminidrone_fc.kicad_sch
Minidrone fc: common questions
What microcontroller does the Minidrone fc use?
The Minidrone fc is built around the XIAO_ESP32C3, from the ESP32 family.
How big is the Minidrone fc PCB?
The Minidrone fc measures 50 × 64 mm, has 4 copper layers and is 0.8 mm thick.
How many components are on the Minidrone fc?
37 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the Minidrone fc design files?
From the yisikawa/minidrone_fc repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Minidrone fc design in my own project?
The repository has no license, so all rights stay with yisikawa. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Minidrone fc without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k