ESP32S3 Carrier
Yoursel71·ESP32S3_Carrier
About the ESP32S3 Carrier PCB
ESP32S3 Carrier is an open source ESP32 PCB design by Yoursel71, published on GitHub. It is a 2-layer board measuring 116 × 200 mm, with 72 components from 41 distinct parts.
Its main chip is the ESP32-S3-DevKitC-1 N16R8, from the ESP32 family. Other key parts include the AMS1117-3.3, VS1838B, TP4056 module (protected) and MT3608 boost module (set 5.3V). By type, the board carries 21 resistors, 18 capacitors, 10 connectors, 8 switches, 5 ICs and 5 diodes.
It belongs with the rf & radio, displays & leds and power & battery designs in this gallery.
From the project
2-layer KiCad 10 carrier PCB for the ESP32-S3-DevKitC-1: CC1101, 2x NRF24, PN532, RDM6300, Si5351, microSD, OLED, 3x IR, buzzer
A 2-layer handheld carrier PCB for the ESP32-S3-DevKitC-1 (N16R8). Every module plugs into 2.54 mm female header sockets; the board itself only carries the sockets, buttons, power circuitry, IR parts and passives.
Enable the internal pull-ups for the buttons. On DevKitC-1 v1.1, IO38 also drives the on-board RGB LED, so the button works but the RGB LED cannot be used at the same time. GDO2 and the two NRF24 IRQ lines are optional; firmware may ignore them.

Main components on the ESP32S3 Carrier
ESP32S3 Carrier bill of materials (BOM)
72 components, 41 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DevKitC-1 N16R8 | ESP32-S3-DevKitC-1_Socket | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | VS1838B | Vishay_MINICAST-3Pin | U3 |
| 1 | TP4056 module (protected) | TP4056_Module_Pads | U4 |
| 1 | MT3608 boost module (set 5.3V) | MT3608_Module_Pads | U5 |
| 2 | PN2222A | TO-92_Inline_Wide | Q1, Q2 |
| 2 | AO3401A | SOT-23 | Q3, Q4 |
| 1 | CC1101 433MHz SMA | CC1101_SMA_2x4_Socket | J1 |
| 1 | NRF24L01+PA+LNA #1 | NRF24L01_PA_LNA_Socket | J2 |
| 1 | NRF24L01+PA+LNA #2 | NRF24L01_PA_LNA_Socket | J3 |
| 1 | PN532 V3 (I2C) | PN532_V3_I2C_Socket | J4 |
| 1 | OLED 1.3in SH1106 I2C | OLED_1.3in_I2C_Socket | J5 |
| 1 | Catalex microSD | microSD_Catalex_Socket | J6 |
| 1 | RDM6300 125kHz | RDM6300_Socket | J7 |
| 1 | 125kHz coil | PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | Si5351 clock gen (3x SMA) | Si5351_3SMA_Socket | J9 |
| 1 | 18650 BAT | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J10 |
| 1 | Passive buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | UP | SW_PUSH_6mm | SW1 |
| 1 | DOWN | SW_PUSH_6mm | SW2 |
Show 21 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LEFT | SW_PUSH_6mm | SW3 |
| 1 | RIGHT | SW_PUSH_6mm | SW4 |
| 1 | OK | SW_PUSH_6mm | SW5 |
| 1 | BACK | SW_PUSH_6mm | SW6 |
| 1 | MODULE PWR | SW_Slide_SPDT_Angled_CK_OS102011MA1Q | SW7 |
| 1 | MAIN PWR | SW_Slide_SPDT_Angled_CK_OS102011MA1Q | SW8 |
| 3 | IR LED 940nm | LED_D5.0mm_Horizontal_O1.27mm_Z3.0mm | D1, D2, D3 |
| 1 | 1N4148 | D_DO-35_SOD27_P7.62mm_Horizontal | D4 |
| 1 | SS34 | D_SMA_Handsoldering | D5 |
| 12 | 100NF 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3, C5, C7, C8, C9, C10, C11 +4 |
| 4 | 100UF 100uF | CP_Radial_D6.3mm_P2.50mm | C2, C4, C6, C15 |
| 1 | 10UF 10uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C12 |
| 1 | 470UF 470uF | CP_Radial_D8.0mm_P3.50mm | C13 |
| 3 | 4.7K 4.7k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R8 |
| 1 | 220 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 7 | 10K 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R7, R9, R12, R13, R14, R15 |
| 3 | 47 | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R5, R17, R18 |
| 1 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | 1M | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10 |
| 1 | 100 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11 |
| 4 | 100K 100k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R16, R19, R20, R21 |
ESP32S3 Carrier design files
The KiCad project lives in the Yoursel71/ESP32S3_Carrier repository on GitHub; these links point at the commit this page was built from.
- LayoutESP32S3_Carrier.kicad_pcb
- SchematicESP32S3_Carrier.kicad_sch
- BOMoutput/BOM.csv
ESP32S3 Carrier: common questions
What microcontroller does the ESP32S3 Carrier use?
The ESP32S3 Carrier is built around the ESP32-S3-DevKitC-1 N16R8, from the ESP32 family.
How big is the ESP32S3 Carrier PCB?
The ESP32S3 Carrier measures 116 × 200 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32S3 Carrier?
72 components, from 41 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESP32S3 Carrier design files?
From the Yoursel71/ESP32S3_Carrier repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ESP32S3 Carrier design in my own project?
The repository has no license, so all rights stay with Yoursel71. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP32S3 Carrier without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k