Photophage
yoyoslayer·Photophage·Project Files/Tamagotchi Device.kicad_pcb
About the Photophage PCB
Photophage is an open source ESP32 PCB design by yoyoslayer, published on GitHub. It is a 2-layer board measuring 62.7 × 87.5 mm, with 9 components from 7 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the HS96L03W2C03. By type, the board carries 3 switches, 2 ICs, 1 connector, 1 battery holder and 1 LED.
From the project
- The pets face will change depending on how it's feeling. It will be happy if it is doing well okay if it is getting by and sad if something is wrong. - There is a light that will change color depending on how the pet is feeling: green means it is happy amber means it is okay an
- The pets face will change depending on how it's feeling. It will be happy if it is doing well okay if it is getting by and sad if something is wrong. - There is a light that will change color depending on how the pet is feeling: green means it is happy amber means it is okay and red means it needs help. - When you press a button the pet will make a beep. - The pet can tell if it is in sunlight or indoor light and it will show you this every minutes. If it is dark it will not say anything. - The pet runs on a battery that you can recharge and it lives in a custom egg-shaped case that I made.
Main components on the Photophage
Photophage bill of materials (BOM)
9 components, 7 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U1 |
| 1 | HS96L03W2C03 HS(汉昇) | OLED-TH_L27.8-W27.2-P2.54_C9900033791 | U2 |
| 1 | Conn_01x06 | PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | Battery_Cell | PinHeader_1x02_P2.54mm_Vertical | BT1 |
| 1 | 1207-P6.5MM XHXDZ(兴华鑫) | BUZ-TH_BD12.5-P6.50-D1.4 | BUZZER1 |
| 3 | SW_Push | SW-TH_4P-L4.5-W4.5-P3.00-LS4.8 | SW1, SW2, SW3 |
| 1 | WS2812D-F5 worldsemi | LED-TH_4P-BD5.8-P1.30 | LED1 |
Photophage design files
The KiCad project lives in the yoyoslayer/Photophage repository on GitHub; these links point at the commit this page was built from.
Photophage: common questions
What microcontroller does the Photophage use?
The Photophage is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Photophage PCB?
The Photophage measures 62.7 × 87.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Photophage?
9 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Photophage design files?
From the yoyoslayer/Photophage repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Photophage design in my own project?
The repository has no license, so all rights stay with yoyoslayer. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Photophage without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k