Giessanlage
YuliRox·Giessanlage·schematics/giessanlage/giessanlage.kicad_sch
About the Giessanlage PCB
Giessanlage is an open source ESP32 PCB design by YuliRox, published on GitHub. It is a board, with 26 components from 14 distinct parts.
Its main chip is the ESP32-C6-DevKitC-1, from the ESP32 family. By type, the board carries 8 resistors, 3 transistors, 3 switches, 2 connectors, 2 diodes and 1 IC.
It belongs with the iot & wireless, displays & leds and sensors designs in this gallery.
From the project
Solar-powered ESP32-C6 plant watering controller. Two channels, MOSFET pump driver, three buttons. Talks to a local MQTT broker for status / config (in progress).
Solar-powered ESP32-C6 plant watering controller. Two channels, MOSFET pump driver, three buttons. Talks to a local MQTT broker for status / config (in progress).
- Controller: ESP32-C6-DevKitC-1 - Pumps: 2× DC pump, ~14 V / 24 W, switched low-side via IRLZ34N N-MOSFETs - Sensors: Chirp soil moisture (I2C), VL53L0X TOF (I2C), A02YYUW ultrasonic (UART) - Display: 2.9" tri-colour e-paper, SPI (Reichelt #253924)
Main components on the Giessanlage
Giessanlage bill of materials (BOM)
26 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C6-DevKitC-1 | ESP32-C6-DevKitC-1 | U1 |
| 2 | IRLZ34N | TO-220-3_Vertical | Q1, Q2 |
| 1 | NX2301P | SOT-23 | Q3 |
| 2 | Pumpe | P1, P2 | |
| 1 | Akku | BT1 | |
| 4 | — | Chirp1, Ultraschall1, eInk1, tof1 | |
| 1 | Solar Charge Controller | SC1 | |
| 1 | Solar_Cell | SC2 | |
| 2 | P1_Manuell_On | SW1, SW2 | |
| 1 | Manuell_Off | SW3 | |
| 2 | 1N4004 | D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2 |
| 3 | 100 | R1, R3, R7 | |
| 3 | 10k | R2, R4, R8 | |
| 2 | 4.7k | R5, R6 |
Giessanlage design files
The KiCad project lives in the YuliRox/Giessanlage repository on GitHub; these links point at the commit this page was built from.
Giessanlage: common questions
What microcontroller does the Giessanlage use?
The Giessanlage is built around the ESP32-C6-DevKitC-1, from the ESP32 family.
How many components are on the Giessanlage?
26 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Giessanlage design files?
From the YuliRox/Giessanlage repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Giessanlage design in my own project?
The repository has no license, so all rights stay with YuliRox. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Giessanlage without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k