Blood-Oxygen and-Heart-Rate-Monitoring-System
Zabauski·Blood-Oxygen-and-Heart-Rate-Monitoring-System·electrical-schematics/schematic.kicad_sch

About the Blood-Oxygen and-Heart-Rate-Monitoring-System PCB
Blood-Oxygen and-Heart-Rate-Monitoring-System is an open source ESP32 PCB design by Zabauski, published on GitHub. It is a board, with 10 components from 7 distinct parts.
Its main chip is the ESP32-S2-WROVER, from the ESP32 family. Other key parts include the MAX30102. By type, the board carries 3 resistors, 2 ICs, 2 diodes, 1 connector, 1 buzzer and 1 LED.
It belongs with the displays & leds, wearables and sensors designs in this gallery.
From the project
Simple device for measuring heart rate and blood oxygen saturation (SpO₂) using a dedicated sensor, with live results displayed on an OLED screen.
Design of a simple device for measuring heart rate and blood oxygen saturation (SpO₂) using a dedicated sensor, with live results displayed on an OLED screen. The device also signals when critical values are exceeded via an LED or an audible buzzer.
- 1 Project Plan - 1.1 Project Components - 2 Bill of Materials - 3 Operating Principle - 4 Schematics - 4.1 Electrical Schematic (Fritzing) - 4.2 Wiring Diagram (KiCad) - 5 Project Implementation - 5.1 Stage 1 – Breadboard - 5.1 Stage 2 – Enclosure Modelling - 5.1 Stage 3 – Printing the Enclosure - 5.1 Stage 4 – Assembling the Electronics - 5.2…
Main components on the Blood-Oxygen and-Heart-Rate-Monitoring-System
Blood-Oxygen and-Heart-Rate-Monitoring-System bill of materials (BOM)
10 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S2-WROVER | ESP32-S2-WROVER | U1 |
| 1 | MAX30102 | Maxim_OLGA-14_3.3x5.6mm_P0.8mm | U2 |
| 1 | USB3_A | J1 | |
| 1 | Buzzer | BZ1 | |
| 1 | OLED-128O064D | OLED-128O064D | DS1 |
| 2 | LED | D1, D2 | |
| 3 | R | R1, R2, R3 |
Blood-Oxygen and-Heart-Rate-Monitoring-System design files
The KiCad project lives in the Zabauski/Blood-Oxygen-and-Heart-Rate-Monitoring-System repository on GitHub; these links point at the commit this page was built from.
Blood-Oxygen and-Heart-Rate-Monitoring-System: common questions
What microcontroller does the Blood-Oxygen and-Heart-Rate-Monitoring-System use?
The Blood-Oxygen and-Heart-Rate-Monitoring-System is built around the ESP32-S2-WROVER, from the ESP32 family.
How many components are on the Blood-Oxygen and-Heart-Rate-Monitoring-System?
10 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Blood-Oxygen and-Heart-Rate-Monitoring-System design files?
From the Zabauski/Blood-Oxygen-and-Heart-Rate-Monitoring-System repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Blood-Oxygen and-Heart-Rate-Monitoring-System design in my own project?
The repository has no license, so all rights stay with Zabauski. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Blood-Oxygen and-Heart-Rate-Monitoring-System without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k