Esc

zayinconde·escPCB·Previous versions/escPCB v1.0/escPCB.kicad_pcb

Esc PCB layout, top view — open source RP2040/RP2350 board by zayinconde

About the Esc PCB

Esc is an open source RP2040/RP2350 PCB design by zayinconde, published on GitHub under the MIT license. It is a 2-layer board measuring 58 × 99.5 mm, with 77 components from 26 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the W25Q16JVSNIQ and LD1117S33TR_SOT223. By type, the board carries 27 resistors, 16 capacitors, 15 transistors, 6 connectors, 3 ICs and 2 switches.

It belongs with the robotics & motion designs in this gallery.

From the project

Three-Phase Brushless Electronic Speed Controller (ESC) designed to drive and control an HW 3660 13.5T BLDC motor.

Main components on the Esc

Esc bill of materials (BOM)

77 components, 26 distinct parts.

QtyPartRefs
1
W25Q16JVSNIQ
IC1
1
RP2040
U1
1
LD1117S33TR_SOT223
U2
6
BC857
Q1, Q2, Q3, Q10, Q11, Q12
9
BC847
Q4, Q5, Q6, Q7, Q8, Q9, Q13, Q14 +1
1
ABM8-272-T3
X1
1
Terminal
J1
1
2137160001
J2
1
XT60-M
J3
2
Conn_01x03_Pin
J4, J5
1
Conn_01x02_Pin
J6
3
IPD70P
AH1, BH1, CH1
3
IPD70N
AL1, BL1, CL1
1
LM211N
CR1
2
431183015816
S1, S2
2
1u
C1, C15
9
100n
C2, C3, C4, C9, C10, C11, C12, C13 +1
1
10u
C5
1
100u
C6
2
15p
C7, C8
Show 6 more
QtyPartRefs
1
C
C16
18
1k
R1, R2, R3, R4, R5, R6, R7, R8 +10
2
5k1
R17, R18
2
27
R19, R20
4
33k
R21, R22, R23, R24
1
10k
R26

Esc design files

The KiCad project lives in the zayinconde/escPCB repository on GitHub; these links point at the commit this page was built from.

Esc: common questions

What microcontroller does the Esc use?

The Esc is built around the RP2040, from the RP2040/RP2350 family.

How big is the Esc PCB?

The Esc measures 58 × 99.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Esc?

77 components, from 26 distinct parts. The full bill of materials is listed on this page.

Where can I download the Esc design files?

From the zayinconde/escPCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Esc design in my own project?

Yes, under the terms of its MIT license, which zayinconde chose for the repository.

Can I test firmware for the Esc without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards