ESP-ISP
ZDBioHazard·ESP-ISP
About the ESP-ISP PCB
ESP-ISP is an open source ESP8266 PCB design by ZDBioHazard, published on GitHub. It is a 2-layer board measuring 18 × 28 mm, with 25 components from 13 distinct parts.
Its main chip is the ESP-12, from the ESP8266 family. Other key parts include the XC6206. By type, the board carries 11 resistors, 5 diodes, 3 capacitors, 2 ICs, 2 transistors and 1 connector.
From the project
A UART programming jig for ESP-12 modules using pogo-pins.
This is just a simple programming jig for the ESP-12 module.
When putting this device together, use <=40-mil pogo pins for the ESP pins. You can then place this device on top of a ESP-12 unit to access it's serial port. (Be careful not to short any of the pogo pins on the metal can though. It can be tricky!)
P1 is normal FTDI header. 5V should work. SW1 is a reset switch. Hold it down for >5s to bring GPIO0 low and release to start flash mode. D5 should light up when GPIO0 is low. D3 is a power indicator. D2` should light up when the ESP is receiving serial data.

Main components on the ESP-ISP
ESP-ISP bill of materials (BOM)
25 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP-12 | ESP-12-ISP | U1 |
| 1 | XC6206 | SOT-23 | U2 |
| 2 | 2N7002 | SOT-23 | Q1, Q2 |
| 1 | FTDI_BASIC | Pin_Header_Simple_1x06 | P1 |
| 1 | RESET | SMD_PUSHBUTTON_3.6x6.0mm | SW1 |
| 2 | 1N5819 | DO-214BA | D1, D2 |
| 2 | GREEN | LED_1206 | D3, D4 |
| 1 | RED | LED_1206 | D5 |
| 2 | 1uF | C_0805 | C1, C2 |
| 1 | 2.2uF | C_0805 | C3 |
| 6 | 10K | R_0805 | R1, R2, R3, R4, R5, R6 |
| 2 | 1M | R_0805 | R7, R8 |
| 3 | 220 | R_0805 | R9, R10, R11 |
ESP-ISP design files
The KiCad project lives in the ZDBioHazard/ESP-ISP repository on GitHub; these links point at the commit this page was built from.
- Layoutespisp.kicad_pcb
ESP-ISP: common questions
What microcontroller does the ESP-ISP use?
The ESP-ISP is built around the ESP-12, from the ESP8266 family.
How big is the ESP-ISP PCB?
The ESP-ISP measures 18 × 28 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP-ISP?
25 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the ESP-ISP design files?
From the ZDBioHazard/ESP-ISP repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the ESP-ISP design in my own project?
The repository has no license, so all rights stay with ZDBioHazard. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP-ISP without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
Similar boards
ESP8266
ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1kESP8266
HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738ESP8266
RatGDO-OpenSource-Bare-ESP8266
Kaldek
55 × 82.7 mm20 parts2LMIT506ESP8266
RatGDO-OpenSource-D1Mini-ESP8266
Kaldek
47.8 × 63.3 mm12 parts2LMIT506ESP8266
Goatgdo
Kaldek
32.9 × 53.3 mm23 parts2LMIT506ESP8266
Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398