23 open source boards using the ESP-12

Real designs built with the ESP-12, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

23 boardsClear filters|Most starred

How designs wire the ESP-12

Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the ESP-12 connects to, and the resistors, capacitors and other passives placed on it.

  • Pin 12 has a pull-up to 3.3V on 13 of 16 designs, most often 10 kΩ (then 20 kΩ).
  • Pin 3 has a pull-up to 3.3V on 12 of 16 designs, most often 10 kΩ (then 20 kΩ).
  • Pin 8 is tied to 3.3V on 14 of 16 designs (a signal on 2).
  • Pin 9 is tied to GND on 14 of 16 designs (a signal on 2).
Pin 1Connected to: A connector 25%
  • Pull-up to 3.3V on 69% · 10 kΩ (9), 50 kΩ (1), 20 kΩ (1)
Pin 2Connected to: A connector 27% · not connected 40%
  • Resistor to GND on 47% · 10 kΩ (2), 100 kΩ (2), 820 Ω (1)
  • Series resistor on 40% · 10 kΩ (6), 68 Ω (1), 9.1 kΩ (1)
Pin 3Connected to: Signal 88%
  • Pull-up to 3.3V on 75% · 10 kΩ (11), 20 kΩ (1)
Pin 8Connected to: 3.3V 88%
  • Decoupling capacitor on 50% · 100 nF (4), 1 µF (2), 4.7 µF (2)
Pin 9Connected to: GND 88%
Pin 10Connected to: A connector 31%
  • Resistor to GND on 69% · 10 kΩ (9), 20 kΩ (2)
Pin 11Connected to: A connector 31%
  • Pull-up to 3.3V on 38% · 10 kΩ (5), 20 kΩ (1)
Pin 12Connected to: A connector 56%
  • Pull-up to 3.3V on 81% · 10 kΩ (8), 20 kΩ (2), 1 kΩ (1)
Pin 13Connected to: A connector 47%
  • Pull-up to 3.3V on 33% · 10 kΩ (3), 4.7 kΩ (2)

7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Internet of-Things-Power-Meter by Nurgak, ESP-AHT10-Extra by c-, Wifi2can by zhangxuhong1024 and Core pcb by plantbot.

The ESP-12 in open source designs

The gallery holds 23 open source boards using the ESP-12 from 16 GitHub repositories; a typical one measures about 64 × 50 mm and carries around 43 components.

100% are two-layer designs, the rest use four layers or more, and 61% carry an open source license.

The most starred is Internet of-Things-Power-Meter by Nurgak.

Microcontrollers on boards using the ESP-12

ESP-12: common questions

Where can I find a ESP-12 reference design?

Each of the 23 boards on this page is a real design using the ESP-12. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ESP-12 pin 12?

Pin 12 has a pull-up to 3.3V on 13 of 16 designs, most often 10 kΩ (then 20 kΩ). Counted from the KiCad layouts of 16 open source designs using the ESP-12.

What pull-up resistor is used on the ESP-12 pin 3?

Pin 3 has a pull-up to 3.3V on 12 of 16 designs, most often 10 kΩ (then 20 kΩ). Counted from the KiCad layouts of 16 open source designs using the ESP-12.

How is the ESP-12 pin 8 connected?

Pin 8 is tied to 3.3V on 14 of 16 designs (a signal on 2). Counted from the KiCad layouts of 16 open source designs using the ESP-12.

What parts are used alongside the ESP-12?

The 24LC02, AC/DC, AMS1117-3.3, AP111733 and AP1117D33 appear in the most repositories here.

Which microcontrollers do boards using the ESP-12 use?

Most are built on ESP8266 (23).

How big is a typical board using the ESP-12?

The median is 64 × 50 mm, and 100% are two-layer designs.

What is the most popular open source board using the ESP-12?

By GitHub stars, Internet of-Things-Power-Meter by Nurgak, with 37 stars.

Can I simulate one of these boards using the ESP-12 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part