ESP32-Mark0
zdenekru·ESP32-Mark0
About the ESP32-Mark0 PCB
ESP32-Mark0 is an open source ESP32 PCB design by zdenekru, published on GitHub under the MIT license. It is a 2-layer board measuring 100 × 100 mm, with 7 components from 7 distinct parts.
Its main chip is the ESP32 Left Side, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 6 connectors and 1 IC.
It belongs with the iot & wireless, displays & leds and sensors designs in this gallery, and the repository also holds 1 earlier revision of it.
From the project
First trial to utilize ESP32-Wroom-32E NodeMCU with BME280 and eInk display. Made with KiCAD 9.0
ESP32 Mark0 is a powerful and not-so-compact IoT development project based on the ESP32-WROOM-32 microcontroller. This project showcases both hardware and firmware design, with a focus on wireless communication, embedded control, and a simple web dashboard interface.
- Prototype embedded systems using Wi-Fi and basic web interface - Interface with sensors and other potential peripherals - Provide a physical platform for experimenting with ESP32 capabilities - Demonstrate firmware/web integration between Arduino and Python/HTML
Main components on the ESP32-Mark0
ESP32-Mark0 bill of materials (BOM)
7 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DHT11 | PinSocket_1x03_P2.54mm_Vertical | U1 |
| 1 | USB_C_Receptacle_PowerOnly_6P | USB_C_Receptacle_GCT_USB4135-GF-A_6P_TopMnt_Horizontal | J1 |
| 1 | eInk display SPI | PinSocket_1x07_P2.54mm_Vertical | J2 |
| 1 | Free GPIOs from Left Side | PinSocket_1x10_P2.54mm_Vertical | J3 |
| 1 | Free GPIOs from Right Side | PinSocket_1x07_P2.54mm_Vertical | J4 |
| 1 | ESP32 Left Side | PinSocket_1x15_P2.54mm_Vertical | J6 |
| 1 | ESP32 Right Side | PinSocket_1x15_P2.54mm_Vertical | J7 |
ESP32-Mark0 design files
The KiCad project lives in the zdenekru/ESP32-Mark0 repository on GitHub; these links point at the commit this page was built from.
ESP32-Mark0: common questions
What microcontroller does the ESP32-Mark0 use?
The ESP32-Mark0 is built around the ESP32 Left Side, from the ESP32 family.
How big is the ESP32-Mark0 PCB?
The ESP32-Mark0 measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32-Mark0?
7 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the ESP32-Mark0 design files?
From the zdenekru/ESP32-Mark0 repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the ESP32-Mark0 design in my own project?
Yes, under the terms of its MIT license, which zdenekru chose for the repository.
Can I test firmware for the ESP32-Mark0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Earlier revisions in the repo: 25Zak001 ESP32 Mark0
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k