MRPC19
ZeniteSolar·MRPC19·hardware/basicsensormodule.kicad_pcb
About the MRPC19 PCB
MRPC19 is an open source Raspberry Pi PCB design by ZeniteSolar, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 121 × 52.1 mm, with 34 components from 20 distinct parts.
Its main chip is the Raspberry_Pi_2_3, from the Raspberry Pi family. Other key parts include the MCP2551-I/SN, MCP2515-xSO and LM7805. By type, the board carries 11 capacitors, 9 resistors, 5 connectors, 4 diodes, 3 ICs and 1 crystal.
It belongs with the power & battery designs in this gallery.
From the project
Módulo Raspberry Pi CAN 2019
As conexões com o MCP2515 foram realizadas com o SPI0 do Raspberry Pi:
Main components on the MRPC19
MRPC19 bill of materials (BOM)
34 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MCP2551-I/SN | SOIC-8_3.9x4.9mm_P1.27mm | U201 |
| 1 | MCP2515-xSO | SOIC-18W_7.5x11.6mm_P1.27mm | U202 |
| 1 | LM7805 | TO-220-3_Horizontal_TabDown_SMD | U501 |
| 1 | 16MHz | Crystal_HC49-U_Vertical | Y201 |
| 1 | I2C | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | USART | PinHeader_1x04_P2.54mm_Vertical | J401 |
| 1 | Raspberry_Pi_2_3 | PinHeader_2x20_P2.54mm_Vertical | J501 |
| 2 | RJ45 | RJ45_YH59_01 | J601, J602 |
| 1 | 500mA | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F501 |
| 1 | pesd1can | SOT-23_Handsoldering | D201 |
| 2 | LED_RED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D402, D403 |
| 1 | LL4148 | D_MiniMELF_Handsoldering | D501 |
| 7 | 100nF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C102, C201, C202, C205, C401, C502, C503 |
| 2 | 22pF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C203, C204 |
| 2 | 1uF | CP_EIA-6032-20_AVX-F_Pad2.25x2.35mm_HandSolder | C501, C504 |
| 1 | 120 | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R201 |
| 1 | 4k7 | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R202 |
| 2 | 10K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R203, R205 |
| 1 | 22K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R204 |
| 4 | 1k | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R402, R403, R404, R405 |
MRPC19 design files
The KiCad project lives in the ZeniteSolar/MRPC19 repository on GitHub; these links point at the commit this page was built from.
MRPC19: common questions
What microcontroller does the MRPC19 use?
The MRPC19 is built around the Raspberry_Pi_2_3, from the Raspberry Pi family.
How big is the MRPC19 PCB?
The MRPC19 measures 121 × 52.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MRPC19?
34 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the MRPC19 design files?
From the ZeniteSolar/MRPC19 repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the MRPC19 design in my own project?
Yes, under the terms of its GPL-3.0 license, which ZeniteSolar chose for the repository.
Can I test firmware for the MRPC19 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507