Tiny gpu

zishaan1911·tiny-gpu·pcb/tiny_gpu.kicad_pcb

Tiny gpu PCB layout, top view — open source FPGA board by zishaan1911

About the Tiny gpu PCB

Tiny gpu is an open source FPGA PCB design by zishaan1911, published on GitHub. It is a 4-layer board measuring 76 × 56 mm, with 72 components from 28 distinct parts.

Its main chip is the ICE40UP5K-SG48ITR, from the FPGA family. Other key parts include the USBLC6-2SC6, AMS1117-3.3, AP2112K-1.2TRG1, FT2232HL-REEL and 93LC56BT-I/SN. By type, the board carries 30 resistors, 29 capacitors, 7 ICs, 2 crystals, 2 diodes and 1 connector.

From the project

A tiny triangle-rasterising GPU in Verilog on an iCE40UP5K, with a generated 4-layer KiCad board

A small triangle-rasterising GPU written in Verilog for the Lattice iCE40UP5K FPGA, plus the 4-layer board it would run on. A laptop sends triangles over USB, and the GPU fills them into a framebuffer and drives a VGA monitor at 640×480, 60 Hz.

The board is a design only: it is fully routed and passes KiCad's checks, but it hasn't been built.

- Rasteriser (rtl/raster.v): fills one pixel per clock using edge functions. Each edge steps by a single add per pixel, so the scan loop has no multipliers. Setup, which does need multiplies, is pipelined over seven clocks and runs on the FPGA's DSP…

Tiny gpu, from the project README
From the project README

Main components on the Tiny gpu

Tiny gpu bill of materials (BOM)

72 components, 28 distinct parts.

QtyPartRefs
1
USBLC6-2SC6
U1
1
AMS1117-3.3
U2
1
AP2112K-1.2TRG1
AP2112K-1.2
U3
1
FT2232HL-REEL
FT2232HL
U4
1
93LC56BT-I/SN
93LC56B
U5
1
ICE40UP5K-SG48ITR
iCE40UP5K
U6
1
W25Q128JVSIQ
W25Q128JVS
U7
1
ASE-12.000MHZ-LC-T
12MHz
X1
1
X322512MSB4SI
12MHz
Y1
1
HRO TYPE-C-31-M-12
USB-C
J1
1
TL3342F160QG
reset
SW1
1
green
D1
1
orange
D2
4
10u
C1, C4, C5, C27
1
22u
C2
1
1u
C3
19
100n
C6, C10, C11, C12, C13, C14, C15, C16 +11
2
18p
C7, C8
2
4.7u
C9, C19
2
5.1k
R1, R2
Show 8 more
QtyPartRefs
3
100
R3, R29, R30
5
1k
R4, R16, R18, R22, R26
1
12k 1%
R5
9
10k
R6, R8, R9, R10, R11, R12, R13, R14 +1
1
2.2k
R7
3
510
R17, R21, R25
3
2k
R19, R23, R27
3
3.9k
R20, R24, R28

Tiny gpu design files

The KiCad project lives in the zishaan1911/tiny-gpu repository on GitHub; these links point at the commit this page was built from.

Tiny gpu: common questions

What microcontroller does the Tiny gpu use?

The Tiny gpu is built around the ICE40UP5K-SG48ITR, from the FPGA family.

How big is the Tiny gpu PCB?

The Tiny gpu measures 76 × 56 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Tiny gpu?

72 components, from 28 distinct parts. The full bill of materials is listed on this page.

Where can I download the Tiny gpu design files?

From the zishaan1911/tiny-gpu repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Tiny gpu design in my own project?

The repository has no license, so all rights stay with zishaan1911. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Tiny gpu without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug FPGA firmware against it before you order a PCB.

Similar boards