Terraskipper
ZIZO932·Terraskipper
About the Terraskipper PCB
Terraskipper is an open source Raspberry Pi PCB design by ZIZO932, published on GitHub. It is a 2-layer board measuring 73 × 108 mm, with 13 components from 8 distinct parts.
Its main chip is the RaspberryPi_Pico_W, from the Raspberry Pi family. Other key parts include the MAX485E and L78L05_SO8. By type, the board carries 6 modules, 2 ICs, 2 connectors and 2 resistors.
It belongs with the sensors, robotics & motion and rf & radio designs in this gallery.
From the project
Terra Skipper is a bio-inspired soft robot designed for the swampy terrains, saline terrain where standard machinery fails. Mimicking a mudskipper fish, it uses soft limbs to crawl over mud. The robot carries a sensor array (pH, Salinity, GPS, IMU, Ultrasonic) to map soil health in real-time.
This is one of the early designs for TerraSkipper, a mudskipper-inspired robot for agriculture. I wanted to explore using fins and a tail to move across difficult ground, with a mechanism that lowers probes to take soil measurements.
The design also explored a seed-dropping mechanism. This repo keeps the CAD, circuit files, and early control logic from that stage. The later build is in TerraSkipper V2.

Main components on the Terraskipper
Terraskipper bill of materials (BOM)
13 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MAX485E | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | L78L05_SO8 | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | RaspberryPi_Pico_W | RaspberryPi_Pico_W_SMD_HandSolder | A1 |
| 5 | Motor_Servo | TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mm | M1, M2, M3, M4, M5 |
| 1 | 7 in 1 soil sensor 12V | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Conn_01x02_Socket | TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J2 |
| 1 | TFT module with 5 pins | PinHeader_1x05_P2.54mm_Vertical | .1 |
| 2 | R | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R2 |
Terraskipper design files
The KiCad project lives in the ZIZO932/Terraskipper repository on GitHub; these links point at the commit this page was built from.
Terraskipper: common questions
What microcontroller does the Terraskipper use?
The Terraskipper is built around the RaspberryPi_Pico_W, from the Raspberry Pi family.
How big is the Terraskipper PCB?
The Terraskipper measures 73 × 108 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Terraskipper?
13 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Terraskipper design files?
From the ZIZO932/Terraskipper repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Terraskipper design in my own project?
The repository has no license, so all rights stay with ZIZO932. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Terraskipper without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507