Aviator
zkeulr·aviator·DisplayDriver/DisplayDriver.kicad_pcb
About the Aviator PCB
Aviator is an open source ESP32 PCB design by zkeulr, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 100 × 75 mm, with 39 components from 22 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the 74AHCT245 and AMS1117-3.3. By type, the board carries 11 capacitors, 10 resistors, 4 ICs, 3 diodes, 2 connectors and 1 crystal.
Main components on the Aviator
Aviator bill of materials (BOM)
39 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 2 | 74AHCT245 | PW20 | U2, U3 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U4 |
| 1 | UJ20-C-H-G-SMT-TR | CUI_UJ20-C-H-G-SMT-TR | X2 |
| 1 | HTSS-108-01-G-D | IDC-Header_2x08_P2.54mm_Vertical | J1 |
| 1 | HEADER-1X14 | PinHeader_1x14_P2.54mm_Vertical | J2 |
| 2 | Lab Kit | SW_PUSH_6mm | BOOT1, RST1 |
| 1 | 1012 | BAT_1012 | BT1 |
| 3 | CASE_SW | Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | MOL1, MOL2, MOL3 |
| 1 | Vin | Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | MOL4 |
| 1 | ~ | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | LED1 |
| 1 | RED | LED_0603_1608Metric | D1 |
| 2 | GREEN | LED_0603_1608Metric | D2, D3 |
| 2 | 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C4 |
| 2 | 1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C7 |
| 4 | 0.1uF | C_0603_1608Metric | C3, C5, C6, C9 |
| 1 | 100uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8 |
| 2 | C | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C12, C13 |
| 5 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5 |
| 1 | 330 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 22 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7, R8 |
| 2 | 56k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9, R10 |
Aviator design files
The KiCad project lives in the zkeulr/aviator repository on GitHub; these links point at the commit this page was built from.
Aviator: common questions
What microcontroller does the Aviator use?
The Aviator is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Aviator PCB?
The Aviator measures 100 × 75 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Aviator?
39 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the Aviator design files?
From the zkeulr/aviator repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Aviator design in my own project?
Yes, under the terms of its GPL-3.0 license, which zkeulr chose for the repository.
Can I test firmware for the Aviator without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k