Myrp60

zlice·myrp60·kicad/my_rp60.kicad_pcb

Myrp60 PCB layout, top view — open source RP2040/RP2350 board by zlice

About the Myrp60 PCB

Myrp60 is an open source RP2040/RP2350 PCB design by zlice, published on GitHub under the GPL-2.0 license. It is a 2-layer board measuring 285 × 95.8 mm, with 53 components from 14 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the TLV73333PDBV and W25Q128JVS. By type, the board carries 16 capacitors, 5 resistors, 3 ICs, 3 LEDs and 1 crystal.

It belongs with the keyboards designs in this gallery.

From the project

60% keyboard with my preferred bottom/right layout.

60% keyboard with my preferred bottom/right layout.

Uses hacky wiring to save rows and push keys into other cols. This makes for a semi-weird layout in the keymap but it works fine.

Everything is on one side so it is cheaper to fab and so you do not see chips or didodes.

- File > Fabcrication outputs > component placement (to /tmp/fireball-components) - ./kicadpostocpl.py /tmp/myrp60-components/myrp60-top-pos.csv /tmp/myrp60-jlcpcb-placement-pos.cmp.csv` (not in repo)

Main components on the Myrp60

Myrp60 bill of materials (BOM)

53 components, 14 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
RP2040
U3
1
TLV73333PDBV
U4
1
W25Q128JVS
U5
1
CRYSTAL_GND24
Crystal_GND24
Y1
11
—
0, 1, 2, 3, 4, 5, 6, 7 +3
14
—
D_0, D_1, D_2, D_3, D_4, D_5, D_6, D_7 +6
2
—
ALT1, ALT2
1
—
SHFT1
10
100N
100n
C1, C2, C3, C4, C5, C6, C7, C8 +2
4
1u
C10, C13, C15, C16
2
30P
30p
C18, C19
2
27
R3, R4
1
10K
10k
R5
2
1k
R6, R7

Myrp60 design files

The KiCad project lives in the zlice/myrp60 repository on GitHub; these links point at the commit this page was built from.

Myrp60: common questions

What microcontroller does the Myrp60 use?

The Myrp60 is built around the RP2040, from the RP2040/RP2350 family.

How big is the Myrp60 PCB?

The Myrp60 measures 285 × 95.8 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Myrp60?

53 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Myrp60 design files?

From the zlice/myrp60 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Myrp60 design in my own project?

Yes, under the terms of its GPL-2.0 license, which zlice chose for the repository.

Can I test firmware for the Myrp60 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards