Project-2
ZYIota·Project-2
About the Project-2 PCB
Project-2 is an open source ESP32 PCB design by ZYIota, published on GitHub. It is a 2-layer board measuring 95 × 82.5 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C6-DIP, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
From the project
This is my PCB layout for the starbie, it contains the electrical wiring and connections for the board (the physical arrangement of components and connectors) The blue connections means the electrical connections are at the back of the circuit while the red connections means the
This is my PCB layout for the starbie, it contains the electrical wiring and connections for the board (the physical arrangement of components and connectors) The blue connections means the electrical connections are at the back of the circuit while the red connections means the electrical connections are at the front of the circuit. Connections between components allow communication to occur, hence it is important to connect them according to their ports correctly such as GND to GND and not GND to 5V

Main components on the Project-2
Project-2 bill of materials (BOM)
7 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C6-DIP | XIAO-ESP32-C6-DIP | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | CONN_01X04_PIN Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | CONN_01X08_PIN Conn_01x08_Pin | MPU6050_Module | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10K | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
Project-2 design files
The KiCad project lives in the ZYIota/Project-2 repository on GitHub; these links point at the commit this page was built from.
- LayoutStarbie.kicad_pcb
- SchematicStarbie.kicad_sch
- BOMBOM - Starbie.csv
Project-2: common questions
What microcontroller does the Project-2 use?
The Project-2 is built around the XIAO-ESP32-C6-DIP, from the ESP32 family.
How big is the Project-2 PCB?
The Project-2 measures 95 × 82.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Project-2?
7 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Project-2 design files?
From the ZYIota/Project-2 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Project-2 design in my own project?
The repository has no license, so all rights stay with ZYIota. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Project-2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k