StarBoy
127001-crtl·StarBoy·Firmware/Starboi hopefully.kicad_pcb
About the StarBoy PCB
StarBoy is an open source ESP32 PCB design by 127001-crtl, published on GitHub under the MIT license. It is a 2-layer board measuring 104.9 × 100.6 mm, with 35 components from 17 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the DHT11, AP2112K-3.3 and PCF8574AP. By type, the board carries 9 resistors, 6 capacitors, 4 ICs, 4 diodes, 3 connectors and 1 switch.
From the project
StarBoy is an ESP32-C3-WROOM-02 hardware project for Hack Club's Half Life.
StarBoy is an ESP32-C3-WROOM-02 hardware project for Hack Club's Half Life.
This repo is set up to document build progress, wiring, and milestones as the board comes together (push buttons, 01x07 OLED/sensor socket, and other modules). This project is based off Lil Guy in collaboration with Creature Co..
- Created initial CAD models for the bottom body, top body, PCB area, and keychain. - Designed the first KiCad schematic and PCB layout. - Completed an Electrical Rules Check (ERC) with no errors. - Completed a Design Rules Check (DRC) with 18 errors and 26 warnings. The issues came from…
Main components on the StarBoy
StarBoy bill of materials (BOM)
35 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | AP2112K-3.3 | SOT-23-5 | U3 |
| 1 | PCF8574AP | DIP-16_W7.62mm | U4 |
| 1 | Round OLED Display | PinHeader_1x07_P2.54mm_Vertical | J1 |
| 1 | MPU6050 module | SOIC-16W_7.5x10.3mm_P1.27mm | J2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J4 |
| 4 | SW_Push | SW_PUSH_6mm | Down1, Left1, Right1, Up1 |
| 4 | 330 Ω | R_0805_2012Metric | R_LED1, R_LED2, R_LED3, R_LED4 |
| 1 | SW_Push | SW_PUSH_6mm | SW5 |
| 4 | LED | LED_0805_2012Metric | D1, D2, D3, D4 |
| 4 | 10 µF | C_0805_2012Metric | C1, C2, C5, C6 |
| 1 | 0.1uF | C_0805_2012Metric | C3 |
| 1 | 100 nF | C_0805_2012Metric | C4 |
| 4 | 150 Ω | R_0805_2012Metric | R1, R2, R3, R4 |
| 3 | 10 kΩ | R_0805_2012Metric | R5, R6, R9 |
| 2 | 5.1 kΩ | R_0805_2012Metric | R7, R8 |
StarBoy design files
The KiCad project lives in the 127001-crtl/StarBoy repository on GitHub; these links point at the commit this page was built from.
StarBoy: common questions
What microcontroller does the StarBoy use?
The StarBoy is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the StarBoy PCB?
The StarBoy measures 104.9 × 100.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the StarBoy?
35 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the StarBoy design files?
From the 127001-crtl/StarBoy repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the StarBoy design in my own project?
Yes, under the terms of its MIT license, which 127001-crtl chose for the repository.
Can I test firmware for the StarBoy without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k