Esp32-power actuator board

2ah33d·esp32-power-actuator-board

Esp32-power actuator board layout, top view — open source ESP32 board by 2ah33d

About the Esp32-power actuator board

Esp32-power actuator board is an open source ESP32 PCB design by 2ah33d, published on GitHub. It is a 2-layer board measuring 96 × 58 mm, with 80 components from 35 distinct parts.

Its main chip is the ESP32-WROOM-32E, from the ESP32 family. Other key parts include the IP2326, SY8205FCC, CP2102N-AXX-XQFN24, AMS1117-3.3 and HY2120-CB. By type, the board carries 32 capacitors, 22 resistors, 7 connectors, 6 ICs, 4 diodes and 3 transistors.

It belongs with the robotics & motion and power & battery designs in this gallery.

From the project

Custom 2-layer ESP32 carrier with 2S LiPo boost charging (IP2326), multi-rail regulation, and high-current servo distribution in KiCad.

Main components on the Esp32-power actuator board

Esp32-power actuator board bill of materials (BOM)

80 components, 35 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
IP2326
INJOINIC(英集芯)
U1
1
ESP32-WROOM-32E
U2
1
SY8205FCC
Silergy(矽力杰)
U3
1
CP2102N-AXX-XQFN24
CP2102N-Axx-xQFN24
U4
1
AMS1117-3.3
Advanced Monolithic Systems
U5
1
HY2120-CB
HY2120CB
HYCON(宏康)
U6
1
FS8205A
FS8205A_C908265
FUXINSEMI(富芯森美)
Q1
2
S8050 J3Y(RANGE:200-350)
S8050_C2146
CJ(江苏长电/长晶)
Q2, Q3
1
CONN_01X02_PIN
Conn_01x02_Pin
J1
1
CONN_01X03_PIN
Conn_01x03_Pin
J2
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J3
1
Conn_01x10_Pin
J9
1
Conn_01x04_Pin
J10
1
Conn_01x06_Pin
J11
1
Conn_01x15_Pin
J12
1
C221841
SW_SPST
SW1
2
SW_Push
SW3, SW4
1
10K
10k
TH2
4
C2286
LED_Small
D3, D4, D5, D6
2
2.2UH
2.2uH
L2, L3
Show 15 more
QtyPartRefs
15
0.1UF
0.1uF
C3, C4, C10, C11, C12, C18, C20, C24 +7
8
22UF
22uF
C5, C6, C7, C14, C15, C16, C17, C23
4
10UF
10uF
C8, C9, C22, C26
2
1UF
1uF
C13, C28
2
4.7UF
4.7uF
C19, C21
1
470UF
470uF
C29
4
0.1K
0.1k
R2, R6, R15, R16
3
5.1K
5.1k
R3, R4, R9
1
62K
62k
R5
2
22K
22k
R7, R11
1
0.5
R8
1
3k
R10
1
47K
47k
R12
5
1k
R13, R14, R21, R22, R23
4
10K
R17, R18, R19, R20

Esp32-power actuator board design files

The KiCad project lives in the 2ah33d/esp32-power-actuator-board repository on GitHub; these links point at the commit this page was built from.

Esp32-power actuator board: common questions

What microcontroller does the Esp32-power actuator board use?

The Esp32-power actuator board is built around the ESP32-WROOM-32E, from the ESP32 family.

How big is the Esp32-power actuator board?

The Esp32-power actuator board measures 96 × 58 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Esp32-power actuator board?

80 components, from 35 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Esp32-power actuator board design files?

From the 2ah33d/esp32-power-actuator-board repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Esp32-power actuator board design in my own project?

The repository has no license, so all rights stay with 2ah33d. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Esp32-power actuator board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards