Starpet project
aagu8162·Starpet-project·pcb/starpet.kicad_pcb
About the Starpet project PCB
Starpet project is an open source ESP32 PCB design by aagu8162, published on GitHub under the MIT license. It is a 2-layer board measuring 105.4 × 82.1 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
It belongs with the iot & wireless, sensors and displays & leds designs in this gallery.
From the project
A project based on the starbie project guide from hack club
I used Kicad to build the schematics and then finally build the pcb as per shown in the guide and made some changes in the way my pcb layout looks.I added a silkscreen of my sprite and made a few small customizations. I used the XIAO ESP32-C3 as my microcontoller and Arduino IDE was used for the firmware. The guide had provided a firmware in which I made some changes in the "beginner settings" block of code. I added my own sprite which I wanted to look like a cat and also added some functions for the buttons.
Main components on the Starpet project
Starpet project bill of materials (BOM)
7 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U1 |
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C6-DIP | U2 |
| 1 | Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
Starpet project design files
The KiCad project lives in the aagu8162/Starpet-project repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/starpet.kicad_pcb
- Schematicpcb/starpet.kicad_sch
Starpet project: common questions
What microcontroller does the Starpet project use?
The Starpet project is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starpet project PCB?
The Starpet project measures 105.4 × 82.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starpet project?
7 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Starpet project design files?
From the aagu8162/Starpet-project repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Starpet project design in my own project?
Yes, under the terms of its MIT license, which aagu8162 chose for the repository.
Can I test firmware for the Starpet project without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k