Self-Balancing-Robot
abdelrauf-44·Self-Balancing-Robot·robot_circuit_borad/robot_circuit_borad.kicad_pcb
About the Self-Balancing-Robot PCB
Self-Balancing-Robot is an open source ESP32 PCB design by abdelrauf-44, published on GitHub. It is a 2-layer board measuring 68.6 × 68.6 mm, with 22 components from 11 distinct parts.
Its main chip is the ESP32-C3_SUPERMINI_TH, from the ESP32 family. Other key parts include the L7805 and L293D. By type, the board carries 6 resistors, 4 connectors, 4 diodes, 3 ICs, 3 switches and 2 capacitors.
It belongs with the sensors, robotics & motion and iot & wireless designs in this gallery.
From the project
ESP32-based self-balancing robot using MPU6050 IMU and PID control, with wireless monitoring and tuning via Blynk.
A two-wheeled self-balancing robot based on ESP32 and MPU6050 IMU, implementing PID control to stabilize an inverted pendulum system in real time. The project focuses on practical control engineering, embedded systems, and electromechanical integration.
This project demonstrates the design and implementation of a self-balancing robot using:
Real-time sensor fusion for tilt angle estimation

Main components on the Self-Balancing-Robot
Self-Balancing-Robot bill of materials (BOM)
22 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | L7805 | TO-220-3_Vertical | U2 |
| 1 | L293D | DIP-16_W7.62mm | U3 |
| 1 | ESP32-C3_SUPERMINI_TH | MODULE_ESP32-C3_SUPERMINI | U5 |
| 3 | Conn_01x02_Pin | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1, J2, J4 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 2 | SW_Push | SW_TH_Tactile_Omron_B3F-10xx | SW1, SW2 |
| 1 | SW_Wuerth_450301014042 | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW3 |
| 4 | LED | LED_D3.0mm | D1, D2, D3, D4 |
| 2 | 330uF | CP_Radial_D6.3mm_P2.50mm | C1, C3 |
| 4 | 330 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R4, R5, R6 |
| 2 | 4.7K | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R3 |
Self-Balancing-Robot design files
The KiCad project lives in the abdelrauf-44/Self-Balancing-Robot repository on GitHub; these links point at the commit this page was built from.
Self-Balancing-Robot: common questions
What microcontroller does the Self-Balancing-Robot use?
The Self-Balancing-Robot is built around the ESP32-C3_SUPERMINI_TH, from the ESP32 family.
How big is the Self-Balancing-Robot PCB?
The Self-Balancing-Robot measures 68.6 × 68.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Self-Balancing-Robot?
22 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the Self-Balancing-Robot design files?
From the abdelrauf-44/Self-Balancing-Robot repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Self-Balancing-Robot design in my own project?
The repository has no license, so all rights stay with abdelrauf-44. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Self-Balancing-Robot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k