Self-Balancing-Robot
abdelrhman1040·Self-Balancing-Robot·PCB/Board V2/self balance robot V2.kicad_pcb
About the Self-Balancing-Robot PCB
Self-Balancing-Robot is an open source ESP32 PCB design by abdelrhman1040, published on GitHub. It is a 2-layer board measuring 52.1 × 78.4 mm, with 21 components from 16 distinct parts.
Its main chip is the ESP32_DevKit_V1_DOIT_30GPIOs, from the ESP32 family. Other key parts include the ESP32-DEVKITC-32D and Pololu_Breakout_A4988. By type, the board carries 10 connectors, 3 modules, 3 capacitors, 2 ICs, 2 resistors and 1 switch.
It belongs with the robotics & motion designs in this gallery.
From the project
...
Main components on the Self-Balancing-Robot
Self-Balancing-Robot bill of materials (BOM)
21 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-DEVKITC-32D | MODULE_ESP32-DEVKITC-32D | U1 |
| 1 | ~ | mini360 | U2 |
| 2 | Pololu_Breakout_A4988 | Pololu_Breakout-16_15.2x20.3mm | A1, A2 |
| 1 | ESP32_DevKit_V1_DOIT_30GPIOs | DOIT_ESP32_DEVKIT_30Pins | A3 |
| 1 | PINHD_1x19_Female | PinSocket_1x19_P2.54mm_Vertical | J1 |
| 2 | PINHD_1x4_Male | PinHeader_1x04_P2.54mm_Vertical | J2, J4 |
| 1 | PINHD_1x8_Female | PinSocket_1x08_P2.54mm_Vertical | J3 |
| 1 | PINHD_1x6_Male | PinHeader_1x06_P2.54mm_Vertical | J5 |
| 2 | PINHD_1x3_Male | PinHeader_1x03_P2.54mm_Vertical | J6, J7 |
| 2 | PINHD_2x4_Male | PinHeader_2x04_P2.54mm_Vertical | J8, J9 |
| 1 | Screw_Terminal_2_P3.50mm | TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_Horizontal | J10 |
| 1 | SW_Wuerth_450301014042 | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW1 |
| 2 | 100u | CP_Radial_D5.0mm_P2.50mm | C1, C4 |
| 1 | 470u | CP_Radial_D5.0mm_P2.50mm | C3 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3 |
| 1 | 2.4k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4 |
Self-Balancing-Robot design files
The KiCad project lives in the abdelrhman1040/Self-Balancing-Robot repository on GitHub; these links point at the commit this page was built from.
Self-Balancing-Robot: common questions
What microcontroller does the Self-Balancing-Robot use?
The Self-Balancing-Robot is built around the ESP32_DevKit_V1_DOIT_30GPIOs, from the ESP32 family.
How big is the Self-Balancing-Robot PCB?
The Self-Balancing-Robot measures 52.1 × 78.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Self-Balancing-Robot?
21 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the Self-Balancing-Robot design files?
From the abdelrhman1040/Self-Balancing-Robot repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Self-Balancing-Robot design in my own project?
The repository has no license, so all rights stay with abdelrhman1040. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Self-Balancing-Robot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k