13 open source boards using the ESP32_DevKit_V1_DOIT_30GPIOs
Real designs built with the ESP32_DevKit_V1_DOIT_30GPIOs, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
ESP32-Simple-Thermostat
jrtaylor71
133 × 89.5 mm40 parts2LNo license2ESP32
BarSync
barna81
95 × 60 mm16 parts2LCC-BY-NC-4.01ESP32
PinJammerV01
pinqin
66 × 133.4 mm63 parts2LNo license0ESP32
Self-Balancing-Robot
abdelrhman1040
52.1 × 78.4 mm21 parts2LNo license0ESP32
Self balancing robot
MostafaMokhtar8545
52.1 × 78.4 mm21 parts2LNo license0ESP32
HackBadge
DevX-Dragon
105 × 80 mm7 parts2LNo license0ESP32
ESP32-Simple-Thermostat-PCB no route
jrtaylor71
133 × 89.5 mm39 parts2LNo license2ESP32
Actionneurv0
Rami-Troudi
90.3 × 73.9 mm40 parts2LNo license1ESP32
PAMI Stepper
Rami-Troudi
120.8 × 70.1 mm31 parts2LNo license1ESP32
Pami n20 V2
Rami-Troudi
80 × 65 mm30 parts2LNo license1ESP32
Pami n20 Chimique
Rami-Troudi
67.4 × 50.4 mm18 parts2LNo license1ESP32
Pami n20 Chimique rev-89
Rami-Troudi
86.5 × 60.9 mm18 parts2LNo license1ESP32
Carte Test Tayssir
Rami-Troudi
72 × 58 mm6 parts2LNo license1
How designs wire the ESP32_DevKit_V1_DOIT_30GPIOs
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ESP32_DevKit_V1_DOIT_30GPIOs connects to, and the resistors, capacitors and other passives placed on it.
- The 3.3V pin is tied to 3.3V on 5 of 7 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 3.3Vpin 1 | Connected to: 3.3V 71% · a signal 29% | — |
| GNDpin 2, 29 | Connected to: GND 100% | — |
| VINpin 30 | Connected to: 5V 71% | — |
25 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ESP32-Simple-Thermostat-PCB by jrtaylor71, BarSync by barna81, Actionneurv0 by Rami-Troudi and Self-Balancing-Robot by abdelrhman1040.
The ESP32_DevKit_V1_DOIT_30GPIOs in open source designs
The gallery holds 13 open source boards using the ESP32_DevKit_V1_DOIT_30GPIOs from 7 GitHub repositories; a typical one measures about 86.5 × 73.9 mm and carries around 21 components.
100% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is ESP32-Simple-Thermostat-PCB by jrtaylor71.
Parts used alongside the ESP32_DevKit_V1_DOIT_30GPIOs
Microcontrollers on boards using the ESP32_DevKit_V1_DOIT_30GPIOs
What boards using the ESP32_DevKit_V1_DOIT_30GPIOs are built for
ESP32_DevKit_V1_DOIT_30GPIOs: common questions
Where can I find a ESP32_DevKit_V1_DOIT_30GPIOs reference design?
Each of the 13 boards on this page is a real design using the ESP32_DevKit_V1_DOIT_30GPIOs. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ESP32_DevKit_V1_DOIT_30GPIOs 3.3V pin connected?
The 3.3V pin is tied to 3.3V on 5 of 7 designs (a signal on 2). Counted from the KiCad layouts of 7 open source designs using the ESP32_DevKit_V1_DOIT_30GPIOs.
What parts are used alongside the ESP32_DevKit_V1_DOIT_30GPIOs?
The ESP32-DEVKITC-32D, LM2596S-5 and Pololu_Breakout_A4988 appear in the most repositories here.
Which microcontrollers do boards using the ESP32_DevKit_V1_DOIT_30GPIOs use?
Most are built on ESP32 (13).
How big is a typical board using the ESP32_DevKit_V1_DOIT_30GPIOs?
The median is 86.5 × 73.9 mm, and 100% are two-layer designs.
What is the most popular open source board using the ESP32_DevKit_V1_DOIT_30GPIOs?
By GitHub stars, ESP32-Simple-Thermostat-PCB by jrtaylor71, with 2 stars.
Can I simulate one of these boards using the ESP32_DevKit_V1_DOIT_30GPIOs before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.