RasberryPI-debug-ESP-HAT
abel-msk·RasberryPI-debug-ESP-HAT
About the RasberryPI-debug-ESP-HAT
RasberryPI-debug-ESP-HAT is an open source ESP32 PCB design by abel-msk, published on GitHub. It is a 2-layer board measuring 65 × 56 mm, with 51 components from 16 distinct parts.
Its main chip is the ESP32-C3 Pro Mini, from the ESP32 family. Other key parts include the CAT24C256. By type, the board carries 28 resistors, 11 diodes, 3 connectors, 3 capacitors, 2 ICs and 2 switches.
It belongs with the dev boards & breakouts and test & measurement designs in this gallery.
From the project
Raspberry Pi HAT for debugging ESP32-C3 Pro Mini: GPIO link via 1k series resistors, 16-pin logic analyzer header, power-cycle switch (P-MOSFET), BOOT button, HAT ID EEPROM. KiCad 10, 65×56 mm, 2 layers.
HAT для Raspberry Pi (40-pin), на который ставится плата ESP32-C3 SuperMini. Raspberry Pi может прошивать и отлаживать ESP через UART, управлять её питанием и режимом загрузки, а все выводы ESP выведены на пружинные клеммники для подключения внешних проводов.
Проект сделан в KiCad 10. Текущая версия платы — 2.1.
- Колодка для ESP32-C3 SuperMini. Два гнезда PLS 1×8 (J4, J5). Модуль с впаянными штырями вставляется сверху, его можно снять. - Связь с Raspberry Pi. UART0 Pi ↔ UART ESP, SPI0, несколько GPIO. Все линии идут через последовательные резисторы 1 кОм: это защищает от конфликта выходов…

Main components on the RasberryPI-debug-ESP-HAT
RasberryPI-debug-ESP-HAT bill of materials (BOM)
51 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CAT24C256 | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | ESP32-C3 Pro Mini | ESP32-C3_Pro_mini_socket | U2 |
| 1 | AO3401A | SOT-23 | Q1 |
| 1 | GPIO | PinSocket_2x20_P2.54mm_Vertical | J1 |
| 2 | KF250-2.54-8P | KF250-2.54-8P | J2, J3 |
| 1 | ID_WP | PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | RESET (power cycle) | SW_SPST_Omron_B3FS-100xP | SW1 |
| 1 | BOOT | SW_SPST_Omron_B3FS-100xP | SW2 |
| 1 | GREEN | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 10 | BLUE | LED_0603_1608Metric | D2, D3, D4, D5, D6, D7, D8, D9 +2 |
| 2 | 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3 |
| 1 | 10u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 2 | 3.9k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 15 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4, R5, R6, R7, R8, R9, R10 +7 |
| 1 | 100k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R16 |
| 10 | 1k | R_0603_1608Metric | R19, R20, R21, R22, R23, R24, R25, R26 +2 |
RasberryPI-debug-ESP-HAT design files
The KiCad project lives in the abel-msk/RasberryPI-debug-ESP-HAT repository on GitHub; these links point at the commit this page was built from.
RasberryPI-debug-ESP-HAT: common questions
What microcontroller does the RasberryPI-debug-ESP-HAT use?
The RasberryPI-debug-ESP-HAT is built around the ESP32-C3 Pro Mini, from the ESP32 family.
How big is the RasberryPI-debug-ESP-HAT?
The RasberryPI-debug-ESP-HAT measures 65 × 56 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the RasberryPI-debug-ESP-HAT?
51 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the RasberryPI-debug-ESP-HAT design files?
From the abel-msk/RasberryPI-debug-ESP-HAT repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the RasberryPI-debug-ESP-HAT design in my own project?
The repository has no license, so all rights stay with abel-msk. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the RasberryPI-debug-ESP-HAT without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k